Recommended Trailer Brake Controller for 2019 Chevy Silverado

Question

Question:

I’d like to find out out what’s the best and affordable brake controller setup for my new truck. Planning on buying a new travel trailer and would like to get this setup installed myself kind of a plug and play. Can u please point me in the right direction

asked by: Rich R

1

Helpful Expert Reply:

For a trailer brake controller that combines excellent performance with an affordable price I highly recommend the Tekonsha Primus IQ # TK90160. This is a proportional controller which means it will automatically send back power to the trailer brakes in correspondence to the force you apply to the brakes in your Silverado. It features an easy-to-read LED display with continuous diagnostics to alert you of any potential issues and 3 boost levels that let you fine tune your braking aggressiveness.

If you have the 2019 Chevy Silverado 1500 then you can use the Plug-In Harness # 3064-P to allow for a completely plug-and-play install. If you have the 2500 or 3500 model you will use # 3016 instead. One end of the harness plugs into the brake controller itself while the other end plugs into the factory port behind the dash.

I have attached a couple video demonstrations that you can check out as well.

expert reply by: Chris R

1

Answer 1

Hey Clay, thanks for reaching out. So the part number #90195 is the Tekonsha Prodigy P3 brake controller and the universal 4-wire pigtail. The #TK29UR comes with the #90195 controller but instead of the universal pigtail it comes with the custom…

view full answer...

Answer 2

There are absolutely plug-in wiring adapters for a brake controller for your 2020 Ram 1500, and what you can use is the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In #C51458 Then for a brake controller that doesn't take…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Recommended Trailer Brake Controller for 2019 Chevy Silverado

Featured Help Information

Miscellaneous Media

Continue Researching