Picking Out Replacement Trailer Taillight for Wesbar Part Number # 250-032135

Question

Question:

Looking for a replacement clearance light for the Wesbar manufacturer part # 250-032135. Is this an exact replacement?

asked by: Jeremy

1

Helpful Expert Reply:

I wasn't able to find anything based on the Wesbar part number you mentioned but the great thing about trailer lights is that if you match the dimensions and appearance of the light you have found the correct replacement. So the part # 47-222012 that you referenced would be the correct replacement as long as the appearance matches and the dimensions of 2-5/8" wide x 1-7/8" tall x 7/8" thick also match.

expert reply by: Jameson C

1

Answer 1

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 2

Hello Matt, thanks for reaching out. Atwood is no longer in business, so you are correct that no parts are available for the 61101 actuators. The Demco Hydraulic Brake Actuator #DM72VR can be used to replace it, but it is not necessarily a direct…

view full answer...

Answer 3

There is no difference other than part number between the HDPB340101 and the Fulton Fold-Away Coupler Hinge Kit for 3" x 4" Tongue #FHDPB340301. We only offer the #FHDPB340301, but each bolt onto 3" x 4" trailer tongues (steel…

view full answer...

Answer 4

Hey Brandon, so we do have brake line kits that most likely would work on your EZ Loader trailer but I would need to know the length and type (flexible or hard) to see which would be best fit.

view full answer...

Answer 5

I looked up your EZ Loader part number and it appears to be the same design as the part #AL91AB which for the matching grommet you'd then need the part #A91GB. You'll also need the wiring harness #A46PB.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Picking Out Replacement Trailer Taillight for Wesbar Part Number # 250-032135

Featured Help Information

Miscellaneous Media

Continue Researching