Is a Spacer Needed for the Reese Goose Box for a Lippert 1621 Pin Box

Question

Question:

why do i have a gap between my goose box and my pin box mount. It had a lippert 1621 rotoflex. do i need spacers

asked by: Marvin P

0

Answer 1

That's a good question Barry, and electric brakes like #23-468-469 do use 16 gauge wiring for the pigtails. But we do recommend using 10 gauge to connect to the brakes simply because of how far the wiring generally has to be run on trailers. I…

view full answer...

Answer 2

A parking brake system, also known as an e-brake, can only be used if the brake assemblies are already equipped with a parking brake. Dexter does offer electric brake assemblies with a parking brake, but their standard electric brakes assemblies…

view full answer...

Answer 3

The grease zerk fitting on your MORryde 3000 is M6 x 1.0 according to my contact at MORryde. To replace this you need the following part: Replacement Brass Grease Zerk for Weld-On Hinges - #MA35ZR This was designed for a weld-on hinge but since it…

view full answer...

Answer 4

We do have a lift kit for your Lippert 7K torsion axle but the Dexter Torflex Lift Kits like part #K71-725-02 are designed to fit specific Dexter torsion axles. For example, the above mentioned kit will only fit a #12 Torflex axle that has a 5,500 -…

view full answer...

Answer 5

Hey Jim, thanks for reaching out! It's better just to replace the whole jack out with the Electric Jack w/ Footplate #EJ-3520-BBX. In all of my research for the FIC3500-2 jack there are a lot of unknowns and assumptions out there so it's best…

view full answer...

Answer 6

In order to choose the correct Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter for a trailer you need to know the pin box pattern. The pin box pattern is indirectly listed on the white sticker attached to the pin box brackets on the…

view full answer...

Answer 7

Hello Adam, thanks for reaching out. The #RP97FR spacer kit may be needed, but I will need to know exactly what pin box size is on your camper currently in order to know if the spacers will be required. There should be a sticker on the pin box that…

view full answer...

Answer 8

For a general-purpose safety chain for a standard gooseneck trailer we offer #337BSC3842 from Buyers Products. This is a 42-inch chain with 3/8-inch clevis. The chain is rated for 15,000 pounds. This is sold as a single chain, not a pair. The 36-inch…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Is a Spacer Needed for the Reese Goose Box for a Lippert 1621 Pin Box

Continue Researching