Is Replacement Rubber Bushing for Kodiak Guide Bolt Sleeve # K225RB Sold Individually

Question

Question:

Replacement Rubber Bushing for Kodiak Guide Bolt Sleeve - ABS Compatible - 2,000 lbs - 8,000 lbs, Item # K225RB. Does that part # include two pieces or just one?

asked by: Larry H

1

Helpful Expert Reply:

The Replacement Rubber Bushing for Kodiak Guide Bolt Sleeve # K225RB is sold individually. If you needed two of these you'd need to order a quantity of 2.

expert reply by: Jameson C

1

Answer 1

The 171255UC seal is the same as the Dexter 010-11088/K71-G01-80. We have that same seal available as the Grease Seal Kit- Triple Lip - Inner Diameter 1.719" - Outer Diameter: 2.565" - Qty 2 #DX49CR.

view full answer...

Answer 2

Hey John! Yes, the Hydrastar Ceramic Brake Pads #HYD85FR share the same profile as the Kodiak 250 brake pads. These are interchangeable with the Kodiak Ceramic Brake Pads #K250CP. What kind of trailer are you replacing the brake pads on?

view full answer...

Answer 3

The breakaway switch by law must be powered from its own power source therefore no, you cannot use the trailer's auxiliary battery to power the breakaway. I recommend the Hopkins Engager Push-To-Test Trailer Breakaway Kit part #20099 as this is…

view full answer...

Answer 4

Hey Christopher, the Hydrastar Disc Brake Kit #HYD44VR is not offered with Timken bearings however you can just buy the matching Timken bearing kit separately with the Timken Bearing Kit 15123/ 25580 Bearings, 15245/25520 Races, 412920 Seal #TMK42VR.…

view full answer...

Answer 5

Hey Nakit, thanks for all of the details on your setup. It's pretty rare we get that much info but it is really helpful. So the Kodiak disc brake kit you would want is the #KOD67VR which covers everything you are needing and matches everything as…

view full answer...

Answer 6

We have 6-1/2 inch oval LED lights that are very bright, that are typically referred to as 6 inch lights in the trailer industry. I recommend the Optronics GloLight LED Backup Light for Truck or Trailer - Submersible - 22 Diodes, #BUL111CB, because…

view full answer...

Answer 7

I spoke to my contact at Kodiak and explained to him your situation and he advised that only silicone based grease be used on the bushing that the caliper slides on. He said that if you used petroleum based grease the bushing will swell and the…

view full answer...

Answer 8

When testing the HydraStar Electric Over Hydraulic Actuator part #HBA-10 it is a three pronged approach. The first step when no wires are connected to anything is to attach the white to ground and the black to 12V positive in this configuration the…

view full answer...

Answer 9

Yes, you have a couple of ways to test the Dexter DX Series Electric Over Hydraulic Brake Actuator #K71-651. The first test to try is to connect the white wire to the negative post of the battery. Then connect the black wire to the positive post on…

view full answer...

Answer 10

Yes, you want your entire hub completely filled with grease. This prevents the grease from being flung out of the bearings. If your spindle does not have a grease zerk like the #TRU74FR to fill the hub with grease you can use a device like the…

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

I spoke with my contact at Kodiak and he said that yes you can turn the disc brake hub/rotor to remove the rust and pits. Etched into the backside of the rotor there will be a minimum width clearance or minimum rotor thickness that you can turn to.

view full answer...

Is Replacement Rubber Bushing for Kodiak Guide Bolt Sleeve # K225RB Sold Individually

Product Page this Question was Asked From

Continue Researching