Touch Pad on Lippert Ground Control Leveling System Switches Screens During Operation
Published 12/10/2018
Products Featured in This Question
Question:
Thanks Conner L for your responce. I have 12 volts coming to my control panel. I have 3.2 volts when I check the yellow and red wires. I also have multiple issues with the buttons on my control panel. When I raise the front jacks the right jack stops and the left jack picks up the whole front of the trailer. Im thinking the control panel. Will the control board effect the buttons on the control panel?
asked by: Mark
Expert Reply:
I am assuming you are referring to the Auto Level Control Panel for Lippert Ground Control Leveling System part # LC421484. If that is the case then the first thing you will need to do is obtain a multimeter. Once you have this then you will need to use the ground probe (black handle) and place that on the green wire coming from the back of the harness and then use the power probe (red handle) and place that on the black wire coming from the back of the harness. You should read 12 volts but if you do not have 12 volts you will need to trace this wire back while checking for shorts. I know you said you replaced the batteries last year but it will still be a good idea to check them again to make sure they are fully charged.
If you get 12 volts at the back of the control panel you are then going to want to check the communication singal. In order to do this you will want to use the ground probe and place that on the yellow wire and then place the power probe on the red wire. You should see between 5-7 volts here. If you do then you will need to replace the control panel. If you do not then most likely the control board will need replaced.
If you have the Lippert Components Ground Control 3.0 Automatic Leveling System part # LC358590 you can use the Replacement Control Module for Lippert Ground Control 3.0 Electric Leveling System part # LC304136. If you have the Lippert Ground Control 3.0 Electric Fifth Wheel RV Leveling System part # LC675817 then you can use the Replacement Control Module for Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC346005.
Product Page this Question was Asked From
Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV Leveling System
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Controllers
- Control Panel
- Lippert
more information >
Continue Researching
- Shop: Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV Leveling System
- Q&A: Replacement Control Pad For A Lippert Hydraulic Level Up Leveling System
- Shop: Replacement Control Module for Lippert Ground Control 2.0 Electric Leveling System
- Shop: Replacement Lippert Control Panel with Amp Connector for 4-Point Leveling System
- Video: Review of Lippert Components Trailer Jack - Camper Jack - LC175225
- Video: Review of Lippert Components Trailer Camper Jack - Replacement Control Unit - LC421484
- Video: Lippert Ground Control Leveling System Control Panel Installation - 2019 Grand Design Reflection Fif
- Video: Lippert Ground Control Leveling System Control Panel Review
- Video: In-Depth Review of the Single Axle Trailer Fender w/ Backing Plate
- Search Results: trailer fenders
- Search Results: steel trailer steps
- Search Results: single axle hanger kit
- Search Results: side step trailer fenders
- Shop: CE Smith Steel Step for Trailer Fender - 7" x 3" - Right Front/Left Rear - Qty 1
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Shop: CE Smith Trailer Axle Beam with Standard Spindles - Galvanized - 57-1/2" Long - 1.8K
- Shop: Single Axle Trailer Fender w/ Backing Plate - Ribbed Steel - 13" to 14" Wheels - Qty 1
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Video: Measuring To Choose The Right Trailer Axle
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Q&A: Can I Use Heavier Rated Leaf Springs on Trailer Without Causing Damage
on Accessories and Parts
Mark
12/10/2018
Thanks Conner L for your responce. I have 12 volts coming to my control panel. I have 3.2 volts when I check the yellow and red wires. I also have multiple issues with the buttons on my control panel. When I raise the front jacks the right jack stops and the left jack picks up the whole front of the trailer. Im thinking the control panel. Will the control board effect the buttons on the control panel?