Does Curt Front Hitch # C31067 Fit 2014 Ram 3500

Question

Question:

Looks like web page example has attachments pointed up. I think I need the front hitche receiver with attachment points facing toward the engine. Any help?

asked by: Cheryl D

0

Expert Reply:

We confirmed with Curt that the front hitch part # C31067 is a confirmed fit for your 2014 Ram 3500. I attached a diagram from the install instructions for this hitch for you to check out that shows how it attaches to the trailer frame.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For a 2016 Ram 2500 the correct Curt front hitch is the part #C31015 and not the part #C31067 that you referenced. I checked with Curt for this hitch and there are no fit exclusions for the diesel engine models. This hangs below the front air dam…

view full answer...

Answer 2

When installing the Curt Front Mount Trailer Hitch Receiver, #C31067, the trimming of the front air dam may be required. To get the hitch to fit under the bumper the air dam will most likely need to be trimmed to allow the receiver tube to set nice…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 10

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 11

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 12

Hey David, thanks for reaching out. Yes, the Curt Trailer Hitch Receiver #C82RJ will indeed fit the 2027 Kia Telluride. This hitch is still in the pre-order phase, but it is being going to fit both the 2026 and 2027 Telluride. Right now, we are…

view full answer...

Does Curt Front Hitch # C31067 Fit 2014 Ram 3500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching