Replacement Slider Handle Kit for Reese 20K Slider Base

Question

Question:

My bar for the slider is bent. It releases both sides so it will slide. Can I order the bar only?

asked by: Dan H

0

Expert Reply:

Thanks for the photo of your Reese 20K 5th wheel slider base # RP50024. You need a new slide handle kit # 58161 which fits Pro Series, Reese and Draw-Tite slider bases.

expert reply by: Adam R

0

click to enlarge

Answer 1

The D-Spud of the Phoenix Faucets RV Bathroom Faucet w/ D-Spud #PF212342 is the threaded outlet on the top of the faucet that will allow you to hook up a handheld shower attachment to your faucet. Simply screw on a shower attachment like #PF276045 to…

view full answer...

Answer 2

The D-Spud of the Phoenix Faucets RV Bathroom Faucet w/ D-Spud #PF212342 is the threaded outlet on the top of the faucet that will allow you to hook up a handheld shower attachment to your faucet. Simply screw on a shower attachment like #PF276045 to…

view full answer...

Answer 3

Hey Larry, the Dometic FreshJet 3 part #DMC69ZR that you referenced does not require an additional control board to work. Basically you just need to run the power wires to it and it' ready to go as the controls are internal and on bottom of the…

view full answer...

Answer 4

The handle that actuates the jaws for the #RP30051 Reese 16K fifth wheel hitch is indeed the #58055 replacement handle you mentioned. The Handle, Foam Grip and cotter pin are included. If you need the actuating rod the handle attaches to as well, it…

view full answer...

Answer 5

Thanks for the photo, that was a huge help! You're needing 1/2 inch wire loom, which we sell by the foot as part #459075-1. I'd also use some 1/2 inch loom clamps, part #A0500 to secure the wire loom and hold it where it's supposed to…

view full answer...

Answer 6

Usually, these springs should not have to be replaced unless they are damaged. You will want to check the Reese Replacement Spring, #30776, and make sure it is not damaged and check the Reese 16K Fifth Wheel Hitch, #RP30047, to make sure that there…

view full answer...

Answer 7

The handle that actuates the jaws for the #RP30051 Reese 16K fifth wheel hitch is indeed the #58055 replacement handle you mentioned. The Handle, Foam Grip and cotter pin are included. If you need the actuating rod the handle attaches to as well, it…

view full answer...

Answer 8

Yes, everything you ordered is correct for replacing the handle and actuating rod of your Reese hitch part #RP30047. The part #58055 is the handle. Part #30579 is the actuating rod. Part #58054 is the klip rings. There are no written instructions for…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Slider Handle Kit for Reese 20K Slider Base

Featured Help Information

Miscellaneous Media

Continue Researching