Mounting Bracket Recommendation for Use with Fulton Trailer Fender # F008563

Question

Question:

I recently purchased Fulton Single Axle Trailer Fender with Top Step for 13inch wheels. F008563 part #. What brackets should I order to mount them? and are there instructions on how to do that? Pictures would be great Thank you.

asked by: James T

0

Expert Reply:

The brackets we recommend for use with the Fulton trailer fenders part # F008563 are the CE Smith brackets # CE26098G-2.I attached a picture that shows how these brackets normally hold fenders on. Essentially you put the L up into the top of the inside of the fender on the side that attaches to the trailer and then you attach it to the trailer accordingly.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hey Charles, when using the Mounting Brackets for Trailer Fender #CE26098G-2 to install the Fulton fender part #F008563 the position of the brackets really comes down to what will work best for your individual situation. I think going into the…

view full answer...

Answer 2

I am sorry Mike but we do not sell custom fit fenders for your Forest River R-Pod. The absolute closest thing I could offer would be the CE Smith Single Axle Trailer Fender item #CE17100ATB. It measures 10" Wide x 32" long x 16" tall…

view full answer...

Answer 3

Your guess is correct Dave! The white wire of the LED Trailer Fender Clearance Light part #MCL180ARB is the ground wire and the black wire is the power wire.

view full answer...

Answer 4

We do offer many styles of replacement trailer fenders in plastic, steel and aluminum that you can check out on the page I linked for you. To start, click on your wheel diameter. I reviewed many photos of the 2011 RP-177 and it appears that the steel…

view full answer...

Answer 5

The Fulton Single Axle Trailer Fender with Top Step - Silver Plastic - 13" Wheels - Qty 1 #F008563 can absolutely be drilled to fit the pre-existing fixed brackets on your trailer frame. The capacity of the Polyethylene step will impact the 300…

view full answer...

Answer 6

I'm going to be perfectly honest...the risk is pretty minimal BUT due to the construction differences between bias ply and radial tires the sidewalls do end up flexing differently which could in turn end up with unpredictable ride…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Mounting Bracket Recommendation for Use with Fulton Trailer Fender # F008563

Products Featured in This Question

Continue Researching