Brake Controller Wiring for a 2019 Chevrolet Suburban

Question

Question:

Need to move my P3 to my 2019 Suburban with tow package. Is there a plug I can get?

asked by: Clark

0

Expert Reply:

The wiring harness that you need is part # 3016. One end plugs into the P3 brake controller, part # 90195, and the other end plugs into the connector under the dash of your 2019 Chevy Suburban. Since you have the tow package you'll have that connector.

Take a look at the video I attached. At around the 2:25 mark you'll see the adapter plugged into under the dash.

expert reply by: Charles S

0

Answer 1

The Primus IQ #TK90160 doesn't have instructions that come with a wiring diagram, but we have a picture/diagram on our site that shows which wires are connected to which functions on your vehicle. I attached the diagram for you to view, the wires…

view full answer...

Answer 2

Just about every full sized domestic SUV and truck will be equipped with a factory hitch and 7-way. If it lacks the factory 7-way, there will be a round US CAR connector under the rear bumper or above the spare tire that would plug into a connector…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Brake Controller Wiring for a 2019 Chevrolet Suburban

Featured Help Information

Miscellaneous Media

Continue Researching