Replacement Gooseneck Coupler Recommendation for Setup that Uses 3.5 inch Inner Tube

Question

Question:

My gooseneck needs a new coupler the id is 3.5 square and the coupler is 3inch i would like a 4inch off set. Do you have anything?

asked by: Kirk M

0

Expert Reply:

The only solution we'd have would be an all new outer and inner coupler like the Ram Gooseneck Couple part # GCSQ-25008 as we don't have anything that is designed for a 3-1/2 inch square inner tube. Everything we offer is for 4 inch square tube.

expert reply by: Jameson C

0

Answer 1

There is not an inner gooseneck coupler square tube we carry that has the 3.5 inch outer dimension you referenced. All of the square gooseneck couplers we carry from all brands have the inner sleeve outer measurement of 4 inches on each side like the…

view full answer...

Answer 2

Hi Gerry; they're both going to do the same thing so I would stick with the square #GCSQ-25008 since that is what it looks like it originally had.

view full answer...

Answer 3

Seeing as your 2021 GMC Sierra 2500 Denali recognizes the trailer but then shows the error message once you start driving leads me to believe the issue is with your trailer. I would start by checking the 7-way connector and adding Dielectric Grease…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey Jordan! Based on your measurement you have a Lippert 1116 or 1716. If you want to confirm that feel free to send me the S/N on your pin box. The Gen-Y Nomad you were looking at is for the Rhino Box so that is not a fit. What you need is the Gen-Y…

view full answer...

Answer 8

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 9

Hey Jeff! The MORryde GooseTech 5th Wheel to Gooseneck Pin Box #MR97MV comes with a Demco eZ-Latch. The best option for a lock is the InfiniteRule Lock for Cast Demco eZ-Latch Trailer Couplers #IR66FR. This is designed to for a standard coupler but…

view full answer...

Answer 10

Welcome back John! I'm going to need a bit more information to confirm the MORryde GooseTech item #MR57MV is the correct one. I checked with the manufacturer and your 2024 Dutchman Astorian 230ML 5th wheel trailer comes standard with a Curt…

view full answer...

Answer 11

Hey Mark, the only real downside to an offset ball like the Gen-Y part #GY43XR is going to be that it costs more typically and it would take up more room when stored compared to a non-offset ball like the #C38CR. The handling and weight carrying…

view full answer...

Answer 12

Hey Travis! The right MORryde GooseTech depends on the pin box bolt pattern and GVWR of the Solitude 310GK. If it is a little older it probably has a Lippert 1621, I believe the newer models use the Lippert Rhino. You can ask whoever you're…

view full answer...

Replacement Gooseneck Coupler Recommendation for Setup that Uses 3.5 inch Inner Tube

Products Featured in This Question

Continue Researching