Finding VIN on Trailer to Register and Purchase Tag

Question

Question:

Need to locate a VIN number to register and buy a tag for a trailer

asked by: K A

0

Expert Reply:

A Vehicle Identification Number (VIN) can be found in many different locations on a trailer. It is most common to be found near the coupler on a plaque or embossed into the frame. It however can be anywhere on the trailer frame as there are not consistent rules for this. If you cannot find the VIN anywhere on your trailer frame, you can call your local highway patrol and they can issue one to you so you can register your trailer.

expert reply by: Jason S

0

Answer 1

In order to secure a kayak to the Yakima Rack and Roll Trailer part #Y08107 you'll need some sort of carrier to help hold it in place, I recommend the Lockrack Adjustable XL Watersport Carrier part #LR54FR since it has locks for security and a…

view full answer...

Answer 2

Since you have VIN number, you will simply need to get a bill of sale since he didn't have a title. The DMV won't have record of the trailer because it hasn't been registered with a title yet. With the VIN and a Bill of Sale, you will be…

view full answer...

Answer 3

If you check out the picture I attached you will see where I pointed out where the sticker is that has the VIN on the Yakima Rack and Roll trailers like the part #Y08106. If somehow the sticker is worn off or unreadable my contact at Yakima said that…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Finding VIN on Trailer to Register and Purchase Tag

Continue Researching