Reese Replacement 5th Wheel Hitch Head for a # 3077 5th Wheel Hitch

Question

Question:

Can I replace the head of trailer hitch #30077 with a #58146 head?

asked by: Glen S

0

Expert Reply:

I spoke with my contact at Reese and he informed me that you would want a Replacement Pro Series Head # 58165 for your Reese # 30077 Fifth Wheel Hitch.

I attached an FAQ article on fifth wheel hitches for you to check out also.

expert reply by: Jameson C

0

Answer 1

Since your trailer has a Reese Revolution pin box (which is the best way setup for a truck with as short of a bed as you have), you need a fixed hitch that attaches to a rail kit in four places. The Companion style hitch like you mentioned which…

view full answer...

Answer 2

The jaw spring that your Reese Fifth Wheel Hitch part (Discontinued) RP30081 requires as a replacement is the part #RP58230. To access the spring you will need to take the head off of the hitch and turn it upside down to access the inner workings of…

view full answer...

Answer 3

Yes. The Replacement Reese Head for 16k Fifth Wheel Hitch #58165 is the correct replacement head for your Reese Pro Series Hitch part number-30056. You can replace the handle with the Replacement Handle Kit for Pro Series Fifth Wheel #58180.

view full answer...

Answer 4

I believe what you are asking for is the Replacement Klip Rings for Reese and Draw-Tite Fifth Wheel Hitches #58054 along with the Replacement Actuating Rod for Reese and Draw-Tite Fifth Wheel Trailer Hitches #30579. These parts are compatible with…

view full answer...

Answer 5

I have a solution for you, but the 8100TR model number was in a lot of the older Fan-tastic Create-A-Breeze vents, which have since been discontinued. You can use Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans part #FVK8017-00…

view full answer...

Answer 6

Since you don't have the wiring harness on your previous RV water heater you most likely had an all propane powered unit. The Atwood RV Water Heater w/ Heat Exchange - Gas and Electric - Automatic Pilot - 8,800 Btu - 6 Gal #AT96163 is powered by…

view full answer...

Answer 7

If your Reese Sliding 5th Wheel Hitch like the Kwik-Slide #RP30051 is not locking in the maneuver position then I first just recommend making sure that the legs are mounted squarely in the base rails. Sometimes when a sliding hitch doesn't lock…

view full answer...

Answer 8

Having a 1.25 spindle, it can be a few bearings that will fit. However, there will not be a hub that uses both an inner and outer bearing of this size. With that said, I highly recommend replacing your axles with something that will use a more common…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Reese Replacement 5th Wheel Hitch Head for a # 3077 5th Wheel Hitch

Featured Help Information

Miscellaneous Media

Continue Researching