Torque Spec for Hitch Height Bolts on Reese M5 27K 5th Wheel Hitch

Question

Question:

We are changing the hitch height on the Arch and center assembly. We need to know the torque for the bolts

asked by: Mpbell

0

Expert Reply:

According to the install instructions for the Reese M5 27K 5th Wheel Hitch # RP30922 as of September 2018, the 5/8" bolts that attach the legs to the center section need to be torqued down to 170 ft.lbs.

expert reply by: Conner L

0

Answer 1

Hey Ron. You should be able to but I need to know what bolt pattern your Keystone Cougar pin box has. I'll need the information on the sticker that's attached to your current pin box. The sticker should say date of manufacture, weight…

view full answer...

Answer 2

Hey Mel, yeah the Shocker Hitch #SHK47YR would be an excellent upgrade to your current pin box but the only catch is - it's only going to work with Lippert or Curt Turning Point 5th-wheel pin boxes. If you had a Lippert 1716, 1116, and 0115,…

view full answer...

Answer 3

Between 4 and 6 inches is typically what is recommended as minimum clearance from trailer overhang to bed rails. If you can level your setup by lowering hitch where you'd have 5 inches you should be fine. Especially if you aren't in an area…

view full answer...

Answer 4

When adjusting the height of a pin box such as #LC1191191 it is important to support the pin box when removing the bolts. I recommend 2 or 3 buddies to give you a hand and make sure no one is beneath the pin box while raising or lowering it. With the…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 10

Hi Eric, Thanks for your question. As long as you are able to remove the factory hitch from your 2025 GMC Sierra 2500, the #C96CR will work as a replacement. Of note, the #C96CR will more than likely mount up a bit differently than your factory…

view full answer...

Answer 11

Hi Dennis! The Hellwig Load Pro 35 Heavy Duty Helper Springs with Custom Mounting Kit - Above Axle #HE93XR can potentially raise an unloaded truck a little, but it's going to be very minimal and will really only happen if your suspension is…

view full answer...

Answer 12

Hey Mark, the only real downside to an offset ball like the Gen-Y part #GY43XR is going to be that it costs more typically and it would take up more room when stored compared to a non-offset ball like the #C38CR. The handling and weight carrying…

view full answer...

Torque Spec for Hitch Height Bolts on Reese M5 27K 5th Wheel Hitch

Featured Help Information

Miscellaneous Media

Continue Researching