Gooseneck Ball and Puck Trim Kit for Ford Factory Fifth Wheel Rail Kit

Question

Question:

Is there a puck or trim needed for the hole where the ball goes ? 2014 F 350 superduty. Purchased truck pre-owned no pucks or trim just holes. Ive attached pics. What all do I need for gooseneck set up ?

asked by: George

0

Expert Reply:

For a gooseneck ball to fit the factory rail kit of your 2014 Ford F-350 you'd want the Reese Elite kit part # RP30137 which would fit right into the pucks of your truck. We have the replacement puck trim kit part # RP58458 which will give you the trim rings you are needing.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Thanks for reaching out and providing your photo! To replace the trim rings for the OEM puck system on your 2020 Ford F-250 you'll want the Kit #RP58458 and then to cover up the gooseneck hole we have the part #RP30136. Unfortunately a trim ring…

view full answer...

Answer 2

Thank you for the photo and we do have replacement trim rings for the Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Trailer Hitches #RP30868 in your 2015 GMC Denali. For those you need the Replacement Trim Rings for Reese Elite…

view full answer...

Answer 3

I spoke with my B&W representative who confirms that to install their GNRK1121 #BW77FR Turnover Ball hitch on a 2021 Ford F-150, the center of the 4 inch hole for the gooseneck ball would be placed 42-5/8 inches forward of the rear edge of the…

view full answer...

Answer 4

When installing the B&W Turnoverball Underbed Gooseneck Trailer Hitch part #BWGNRK1116 on a 2019 Ford F-250, you will need to drill the hitch ball hole 45-1/2" back from the edge of the bed. This may or may not line up perfectly with the…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 11

Hey Douglas! The correct Gen-Y gooseneck pin box for your 2022 Forest River Cardinal Red is the #GY33GR. This fits the Rhino bolt pattern and is rated for trailers with a GVWR of 7,275-16,360 lbs. You will also need safety chains #GY49GR to complete…

view full answer...

Answer 12

Hey there Trace! There are parts of the steel brackets that come into contact with the aluminum bed on your new 2026 F350 Super Duty (congrats on the new truck by the way - those are super nice!). B&W says to use strips of polypropylene tape…

view full answer...

Gooseneck Ball and Puck Trim Kit for Ford Factory Fifth Wheel Rail Kit

Continue Researching