Availability of Replacement Capsule for Wesbar 102640 Light

Question

Question:

Can you buy just the replacement capsule 102640. Thanks

asked by: Jim G

0

Expert Reply:

The Wesbar 102640 light assembly features a sealed capsule that cannot actually be replaced. Because of this your best option is to simply replace the light assembly itself. The current version of this light is the Wesbar # 403026 for the Driver Side and # 403076 for the Passenger Side.

I have attached an installation video on this light that you can also check out.

expert reply by: Chris R

0

Answer 1

The Wesbar trailer light 102640 has a sealed capsule so the bulb cannot be replaced. Part 403356 is a replacement capsule but this is no longer made. It is likely to be both easier and less costly in the long run to simply replace that light with LED…

view full answer...

Answer 2

Yeah sorry Adam, that's a bit of a high expectation. The Optronics LED Combination Trailer Tail Lights item #TLL160RK, you were looking at are as close as you can get to the older Wesbar 102640 lights. These submersible LED lights measure…

view full answer...

Answer 3

The SAE STIAP2 04 DOT number you provided is a DOT approval number, which states that the lens is compliant with DOT regulations. Because of that, that number isn't typically a good identifier for finding a replacement lens. However, in this…

view full answer...

Answer 4

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable. If your capsule is sealed, then your best option is to replace the lights with new lights like part #403026 and #403076.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Availability of Replacement Capsule for Wesbar 102640 Light

Featured Help Information

Miscellaneous Media

Continue Researching