Trailer Hub Grease Seal Recommendation for Replacing National Seal 474276

Question

Question:

I am looking for a replacement for a national seal #474276. Now my question is your seal replacememt,which you say is a match is 1.500 ID x1.987 OD, and mine says it is 1.983 OD. Is that difference going to be a problem, thanks

asked by: Larry J

1

Helpful Expert Reply:

Your dimension of 1.983 is close enough to the dimension of the # 10-9 which has outer diameter of 1.987 and the cross reference numbers match so this would be a fit and would work well.

expert reply by: Jameson C

1

Answer 1

I have a solution for you. I went ahead and reached out to my contact at Dexter Axle, and they recommended replacing the surge coupler with a standard weld on or bolt on straight tongue coupler. This is the safest way. They could not confirm for sure…

view full answer...

Answer 2

Thank you for including images, this was a great help to me understanding what you will need to do to equip your trailer with electric brakes. The best thing for you to do is to immobilize the surge coupler. To do this you can weld the inner part of…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Trailer Hub Grease Seal Recommendation for Replacing National Seal 474276

Product Page this Question was Asked From

Continue Researching