Replacement Hubs for a 2001 Forest River RV Flagstaff Folding Pop-Up Camper

Question

Question:

I have a 2001 forest river flagstaff pop up camper. I am needing an entire hub assembly. It’s a 4 lug and the bearing says : VPZ-15-MRI L44610

asked by: James

0

Expert Reply:

The correct trailer hub you need for your 2001 Forest River RV Flagstaff Folding Pop-Up Camper is the Trailer Idler Hub Assembly part # AKIHUB-440-2-2K. I have attached an install video for you as well.

expert reply by: Conner L

0

Answer 1

The difference between the letters D and R on a trailer tire size is to show the different tire's construction. D stands for bias ply and R for radial. The main difference between a radial ply and a bias ply tire is how the tire is constructed.…

view full answer...

Answer 2

A lot of trailer tire blowouts are a result of heat build up that causes the tire to fail. There are several things that can cause too much heat to build up but the main two most likely suspects are overloading the trailer and/or under inflated…

view full answer...

Answer 3

Though we do not have a printable 5 lug bolt pattern sheet I can teach you how to properly measure your rim! Since your rim has 5 bolts you will need to measure from the center of one hole to the farthest edge of either of the two farther holes.…

view full answer...

Answer 4

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Hubs for a 2001 Forest River RV Flagstaff Folding Pop-Up Camper

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching