Replacement Dexter Grease Seal for Seal Part K71-386-00

Question

Question:

I have 2 Dexter 8k axles on my camper and the only number I can find for the seals is k71-386-00. Would the rg06-070 be the correct seal that I would need.

asked by: Josh

0

Expert Reply:

Yes, you can use the seal part # RG06-070. I looked up the K71-386-00 seal that you mentioned and it has matching dimensions, an inner diameter of 2.25 inches and an outer diameter of 3.376 inches. This seal is commonly found on Dexter axles rated from 5200-lbs to 8000-lbs.

expert reply by: Adam R

0

Answer 1

On Redline Wheel Cylinder #BP17-030 the brake line fitting is standardized, 3/8-inch with 24-TPI (24-threads per inch). I confirmed with my contact at Redneck.

view full answer...

Answer 2

For your 3,500 lb Dexter Torsion axles, you will want to use the Torflex Lift Kit - Tandem Axle - 2-5/8" Lift #K71-707-02. This will provide an additional 2-5/8" clearance. The distance between the mounting bolts is 8 inches center on…

view full answer...

Answer 3

Hey John, It's totally normal for trailer tires to heat up and increase in PSI while towing and that's why the tires have a max cold psi rating listed. The max cold psi rating takes into account how much psi will be gained from the tire…

view full answer...

Answer 4

Dexter has confirmed that the #046-124-00 snap in grommet will work with their 7K axles.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Dexter Grease Seal for Seal Part K71-386-00

Product Page this Question was Asked From

Continue Researching