Fitting Size and Thread Pitch for Redline Wheel Cylinder BP17-030

Question

Question:

what is the threading on the connection to the 3/16 brake fluid line. when i tried to make a connection with what exists on my trailer, it binds up. Is it metric threading?

asked by: Dale O

0

Expert Reply:

On Redline Wheel Cylinder # BP17-030 the brake line fitting is standardized, 3/8-inch with 24-TPI (24-threads per inch). I confirmed with my contact at Redneck.

expert reply by: Adam R

0

Answer 1

Yes, you can use the seal part #RG06-070. I looked up the K71-386-00 seal that you mentioned and it has matching dimensions, an inner diameter of 2.25 inches and an outer diameter of 3.376 inches. This seal is commonly found on Dexter axles rated…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 12

Hey Brad, thanks for reaching out. We should have a grease hub for you, but there is no way to use the trailer ID number or VIN to look up exactly what hubs you need. Trailer manufacturers just aren't that specific with their online literature,…

view full answer...

Fitting Size and Thread Pitch for Redline Wheel Cylinder BP17-030

Product Page this Question was Asked From

Continue Researching