Replacement Pins for Lippert Ground Control 3.0 Stabilizing System

Question

Question:

Can I order the shear pins at the top of the legs for these jack ?

asked by: Lonny M

0

Expert Reply:

The only replacement pins available for your Lippert Ground Control 3.0 # LC358590 are the Replacement 3/8" x 3" Snapper Pins # LC225598, which are used to attach the foot pad to the jack.

expert reply by: Kyle S

0

Answer 1

Per the manufacturer when it comes to the shear pins being broken you would have to replace the whole Lippert Jack #LC298707 because the shear pins are not replaceable, and there is no way to fix them. What you will need to do is purchase a whole new…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hey Mike, thanks for reaching out. The Furrion tankless #FR98SR is one of the few options that lines up well with what you’ve got. It’s designed around the same cutout size as your Dometic 94002BP, so you’re not getting into major wall modifications…

view full answer...

Answer 6

Hey Charles. I didn't receive any pictures but they make those Rhino Boxes pretty easy to identify when they slap that giant label on the side pin box. If you would like to email me the pics directly you can send them to the email address you…

view full answer...

Answer 7

Hey Jeffrey, Lippert confirmed that your pin box is a Rhino Box, so I recommend the Shocker Hitch 5th Wheel to Gooseneck Coupler Kit #SHK99YR. You will also need the Safety Chain Kit for Shocker Hitch 5th Wheel to Gooseneck QuickAir Hitch #SHK35MR.…

view full answer...

Answer 8

The Furrion RV Tankless Water Heater part #FR98SR is the same size as the Dometic RV Water Heater part #DMC74FR (WH-6GEA) so there will be no issues with replacement. This however is a gas only unit so there will be no electric hookups.

view full answer...

Answer 9

We have what you need. Yes the Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU #FR93FR will be perfect replacement and you will NOT need a door you can reuse the one you currently have. There might be an access port outside that…

view full answer...

Answer 10

Hello Mark; is this a 2019 Grand Design Reflection? Assuming it is, the lowest listed GVWR is 8,995 lbs on the 220RK. The unloaded weight is 6,695 lbs but that isn't what determines fitment, and you're going to be heavier than that no matter…

view full answer...

Answer 11

The best replacement option we offer for a Dometic WH-6GA RV Water Heater is tankless, the Furrion RV Tankless Water Heater part #FR68SR which is gas only. It won't be a direct replacement but still pretty easy nonetheless as they are very…

view full answer...

Answer 12

The MORryde X-Factor Crossmember part #MR33WR attaches to the leaf spring hangers which are located in-between and in the front and rear of each axle. I have attached a photo below to clarify. Therefore, you'll need three for full support on a…

view full answer...

Replacement Pins for Lippert Ground Control 3.0 Stabilizing System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching