Idler Hub Compatible With Timbren Axle-Less Suspension System
Question:
Will part# 84655UC1-EZ work with this setup? Thanks
asked by: Justin M
Expert Reply:
I can get you a hub assembly that fits, but the Idler Hub Assembly # 84655UC1-EZ will NOT work with the Timbren Heavy-Duty Axle-Less Trailer Suspension # TASR35HDS06.
Instead, you're going to need a hub and drum assembly with this suspension and the correct fit is Hub and Drum Assembly # AKHD-655-6-EZ-K. This assembly is compatible with the Timbren's EZ Lube spindle and uses the correct inner bearing # 25580, outer bearing # 15123 and grease seal # GS-2250DL
Products Referenced in This Question
Replacement Trailer Hub Bearing - 15123
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.250 Inch I.D.
- Bearing 15123
- Race 15245
- 5200 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - 25580
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.750 Inch I.D.
- Bearing 25580
- Race 25520
- 10000 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- 8000 lbs Axle
- 9000 lbs Axle
- etrailer
more information >
Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 6 on 5-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub
- EZ Lube
- Pre-Greased
- L68149 / L44649
- Standard Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Easy Grease Trailer Hub and Drum Assembly for 5.2K & 6K Axles - 12" - 6 on 5-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- EZ Lube
- Pre-Greased
- 25580 / 15123
- Standard Grade
- For 5200 lbs Axles
- For 6000 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- etrailer
more information >
Grease Seal - Double Lip - 2.250" ID - 3.376" OD - GS-2250DL
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 2.250 Inch I.D.
- 3.376 Inch O.D.
- TruRyde
more information >
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 2" Lift - 5 Bolt - 3.5K
- Trailer Axles
- Rubber Spring Suspension
- Standard Grade
- 3500 lbs
- Spindles Only
- Universal Fit
- Lift - 2 Inch
- Timbren
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Can the Trailer Valet Drill Powered Stabilizer Jack Work on Uneven Ground
- Q&A: Recommended Timbren Axle Less System and Hub with 5 on 5-1/2 Bolt Pattern
- Q&A: Brake And Hub/Drum Assemblies For The Timbren Axle-less Trailer Suspension # TASR35HDS06
- Q&A: Recommended Timbren Suspension, Hubs, and Electric Brakes for an Overland Trailer
- Q&A: Option For Putting Larger Tires On A Stealth 20' Car Hauler
- Q&A: Which Hubs Fit the Timbren Heavy-Duty Axle-Less Trailer Suspension # TASR35HDS06 with 2" Lift
- Q&A: How to Determine Correct Replacement Trailer Hub and Spindle
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: How to Install E-Track in 3 Easy Steps
- Article: Trailer Wiring Diagrams
- Article: How to Dump Black and Gray RV Waste Tanks
- Article: How to Change a Trailer Tire
- Article: Where to Position the Trailer Axle?
- Article: Trailer Lighting Requirements