Installing Bearing Buddy Bearing Protectors on EZ Lube Spindle
Updated 05/24/2018 | Published 05/23/2018
Question:
I put bearing Buddies on my boat trailer recently. The hubs have grease fittings in the end of the hub. Should I remove these when using the Bearing Buddies? The Bearing Buddies are installed with the hub grease fittings still on there at the moment
asked by: Mike
Expert Reply:
You can certainly install a Bearing Buddy like # BB1980A-SS on a trailer like yours that is equipped with EZ lube spindles, but you will want to remove the zerk fitting before installing the Bearing Buddy Bearing Protectors. This grease zerk will prevent the Bearing Buddy from lubricating the hub properly.
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.99 Inch
- 2000 lbs Axle
- 2500 lbs Axle
- 3500 lbs Axle
- Bearing Buddy
more information >
Continue Researching
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Search Results: dust caps
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Search Results: rv bearing
- Shop: Kodiak Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 - Galvanized Steel
- Q&A: Hub for E-Z Lube Spindle on Boat Trailer
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles
- Search Results: trailer hubs and drums
- Q&A: Replacement Axle Spindle for Dexter P21-SLR with 76 Inch Spring Seats and 44649 and 68149 Bearings
- Q&A: Can Bearing Buddy Fit on EZ Lube Spindle that has Zerk Fitting
- Video: Timken Bearing Kit Installation - Enclosed Trailer
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Video: Breaking Down the Kodiak Trailer Hub for 3,500-lb Axles
- Shop: Timken Grease and Oil Seal - Double Lip - I.D. 1.719" / O.D. 2.565" - 473336
- Search Results: 1980a
- Video: In-Depth Review of the DeeMaxx Stainless Steel Drive-In Grease Cap w/ Plug
- Video: All You Need to Know About the Peterson Clearance or Side Marker Trailer Light w/ Reflector
- Video: All You Need to Know About the Grease Cap, 1.99" OD EZ Lube Drive in with Plug
- Video: Review of etrailer Trailer Hubs and Drums - Pre Greased Idler Hub - AKIHUB-545-35-K
- Video: Bearing Buddy Bearing Protectors-BB1980A-SS Spec Review
- Q&A: Dexter Hub Vs. Kodiak Hub Comparison
- Q&A: Should There Be A Gap Between The Seal and The Inner Bearing In My Hub
- Search Results: timken
- Search Results: ez lube spindle
- Search Results: disc brake pads
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: What Is Included With The DeeMaxx Disc Brake Kit DE42FR?