Should Trailer Leaf Springs Be Easy to Move Up and Down
Updated 08/22/2011 | Published 08/19/2011
Question:
I already sent a question about the ubolts to you guys, but i was also wondering how stiff should be jetski slipper springs be? right now they are pretty easy to move up and down, do I want it to require a little force? I know they shouldnt be rock stiff but I was curious. Thanks alot
asked by: Hayden M
Expert Reply:
If the slipper springs on your trailer have a lower capacity like # WIC2 at 500 pounds apiece, then it would be possible to physically compress them with the trailer empty but it should not be all that easy. With a load on the trailer it will be easier. If you find that you can move the springs then it is probably time for some new ones.
On higher capacity springs you probably would not be able to move them at all without a load on the trailer. I have included a link to our slipper spring FAQ article for you.
Product Page this Question was Asked From
Replacement U-Bolt for 1-1/2" Wide, Square Trailer Axles - 1/2" Diameter - Raw Finish
- Trailer Suspension Parts
- U-Bolts
- Camper
- Car Hauler
- Utility Trailer
- 3500 lbs
- Square Axle - 1-1/2 Inch
- 1/2 Inch Diameter
- 5 Inch Long
- Redline
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles
- Shop: Timbren Silent Ride Suspension for Single Axle Trailers w/ 2-3/8" Round Axles - 3,500 lbs
- Shop: Timbren Axle-Less Trailer Suspension w/ Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 2K
- Shop: Trailer Wiring
- Q&A: How Much Clearance is Needed to Account for Suspension Travel on a Trailer
- Q&A: How Much Should a Leaf Spring Bend and How Much Distance Should Be Between Axle and Trailer
- Shop: Curt Tail Light Converter with 4-Way Flat Trailer Connector
- Search Results: stabalizer
- Search Results: trailer coupler channel
- Search Results: shackle hanger
- Search Results: stub axle
- Search Results: c channel
- Search Results: hitch channel
- Search Results: idler hub assembly
- Q&A: How to Determine the Capacity of Trailer Leaf Springs and How to Raise the Coupler Height
- Shop: Shackle Bolt with Locknut For Double-Eye Springs - 1/2" Diameter - 3" Long
- Shop: Replacement Shackle Strap - 2-5/8" Long
- Shop: #42 Spindle for 5,200-lb to 7,000-lb Trailer Axles - 2-1/4" Diameter
- Video: DIY 2005 Scion xA Installation for the Curt Tail Light Converter with 4-Way Flat Trailer Connector
- Shop: Trailer Hitch
- Q&A: Boat Trailer Slipper Spring Installation
- Q&A: How Tight Do Leaf Spring Bolts Need To Be?
- Q&A: How Tight Should Leaf Spring Shackle and Spring Eye Bolts Be
- Q&A: Is There a 2" Trailer Hitch Receiver For a 2007 Kia Optima Capable Of Supporting 275lbs?
- Article: Trailer Wiring Diagrams
- Video: How to Choose a Trailer Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
on Trailer Suspension Parts
