Is There a Mounting Bracket for the Kodiak Tee Fitting Part # BH-T-3FIF

Question

Question:

How do you attach this to the frame of the car so it doesnt rattle all day long?

asked by: Todd

0

Expert Reply:

If you are concerned with how to mount the Kodiak Tee Fitting part # BH-T-3FIF then I recommend using the Titan Tee Fitting part # T0778500. This fitting comes with a mounting bracket so you do not have to worry about the tee bouncing around. They both have female 3/8"-24 threads so you will be able to use one in place of the other.

expert reply by: Conner L

0

Answer 1

There are a couple of ways to mount the Kodiak Tee Fitting for Hydraulic Brake Hose - Brass - 3/16" Female Inverted Flares #BH-T-3FIF. Many will use brake line mounting hardware on either side of the brake line which will provide enough…

view full answer...

Answer 2

Here are all the 3/8"-24 unions, elbows and fittings we have. You will need to acquire the line end fitting from a local auto parts store as this is something we do not currently carry. They will also have the correct double flare tool you can…

view full answer...

Answer 3

In regards to the Hopkins Engager Push-To-Test Trailer Breakaway Kit part #20400, there are only two wires with the black being power so it should be run to the positive battery terminal and the blue being brake output so it should be run to the…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Is There a Mounting Bracket for the Kodiak Tee Fitting Part # BH-T-3FIF

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching