Does Timbren Silent Ride Suspension for Tandem Axle Trailers # TSR14KT01 Require Cross Brace Tube

Question

Question:

Where dose the local acquired tube mount between the two units

asked by: Delbert

0

Expert Reply:

The Timbren Silent Ride Suspension kit part # TSR14KT01 does require an axle to be provided. I attached a picture that shows how Timbren recommends sourcing and installing the axle tubing.

expert reply by: Jameson C

0

Answer 1

It seems like the end goal for this is going to be to lower your trailer a little bit; if I'm misunderstanding what the end goal is here please let me know. I'll start this off by saying that the Timbren Silent Ride #TSR14KT01 is not an air…

view full answer...

Answer 2

I really like the Timbren Silent Ride systems like part #TSR14KT01 that is rated for 3" axles and 14,000 lbs. This gets rid of the traditional leaf spring setup and gives you pivoting arms and Double Aeon rubber springs for a better ride…

view full answer...

Answer 3

Great question! The Timbren Silent Ride Suspension for Tandem Axle Trailers w/ 3" Round Axles #TSR14KT01 have an articulation of 1-27/32 so you need to make sure that you have about 4-5/8" of space above your tire. I confirmed this with my…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Does Timbren Silent Ride Suspension for Tandem Axle Trailers # TSR14KT01 Require Cross Brace Tube

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching