Can Gen-Y Torsion Weight Distribution Shank be Used with Husky WD System

Question

Question:

I am upgrading my travel trailer to one with just over 1000 hitch weight, I also carry a SXS in the bed of the truck with the back of the machine behind the rear wheels of the truck. I currently have an extended 12 shank with the Husky trunnion WD with 800-1400 updated trunnion bars. see pic With the Gen Y shank work with my WD head assembly? or is this over kill? My current tow vehicle is Ram 2500 quad cab, short bed with 6.7 cummings. I already have the timbren SES for the rear suspension. Thank you,

asked by: Doug H

1

Helpful Expert Reply:

The Gen-Y Torsion Weight Distribution Shank # 325-GH-1302 referenced in your question can be used with your existing Husky Weight Distribution System, as it is compatible with any standard system like this one. The heavy-duty rubber torsion flex cords will do definitely great job of reducing or eliminating shock transfer and bounce, which will offer great benefit considering the type of load you are hauling. From the center of the hitch pin hole on the shank, to the center of the adjustment holes, there is a distance of 12-1/8 inches. You will just want to make sure this gives you enough clearance for your trailer.

One thing to keep in mind, since you will already have a lot of tongue weight with both the SXS and trailer, is that the shank weighs about 110 pounds by itself. So this will only be adding to the total tongue weight of your setup. Since both the trailer's loaded tongue weight and any added weight coming from behind the truck's rear axle will need to be factored in, I recommend making sure that your existing Husky system is rated properly.

I have attached a short video demonstration on this product that you can also check out.

expert reply by: Chris R

1

click to enlarge

Answer 1

Yes, the Gen-Y Torsion Weight Distribution Shank #325-GH-1302 that you referenced will work with an Equalizer weight distribution system. I attached a picture that shows an Equal-I-Zer brand head attached to this for you to check out as well.

view full answer...

Answer 2

Yes, the Equal-i-zer Weight Dist Shank part #EQ90-02-4900 will work with the Fastway E2 weight distribution system such as the Fastway e2 Weight Distribution w/ 2-Point Sway Control part #FA94-00-0600. As long as the 10" of rise and 6" of…

view full answer...

Answer 3

Blue Ox SwayPro Weight Distribution system #BXW2003 is compatible with the following Gen-Y Torsion Weight Distribution Shanks: #325-GH-1302 (video linked) #325-GH-1102 #325-GH-1202 The Gen-Y shanks accept weight distribution heads with holes spaced…

view full answer...

Answer 4

Weight distributions don't typically have the same weight capacity classifications as other towing products. But if you are looking for a weight distribution system for a Class V hitch with a 2-1/2 inch opening we have great options from Reese.…

view full answer...

Answer 5

A Gen-Y Torsion ball mount like #325-GH-1024 can be used with a Curt MV weight distribution system. You will put the weight distribution system shank in one of the stacked receivers and that will give you a smooth ride and still give you the…

view full answer...

Answer 6

There are many replacement heads available. I've attached a couple links to assist you with the options we currently have available. One is for square bars, one for round bars, and one for trunnion bars. If you can't narrow it down based on…

view full answer...

Answer 7

Thank you for providing a photo of your Pro Series weight distribution hitch #49570. The assembly/installation instructions for this kit are linked for you for reference and they indicate the correct torque specs for the included hardware. It is very…

view full answer...

Can Gen-Y Torsion Weight Distribution Shank be Used with Husky WD System

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching