Recommended Galvanized Idler Hub Assembly for Timbren Axle-Less Trailer Suspension # ASR3500S06
Updated 03/03/2020 | Published 02/27/2018
Products Featured in This Question
Question:
Id like a galvanized idler hub for the Timbren ASR3500S06. Will the AKIHUB-545-35-G-EZ-K work? Thanks!
asked by: Kevin L
Expert Reply:
Yes, the etrailer.com Trailer Idler Hub Assembly # AKIHUB-545-35-G-EZ-K referenced in your question will work perfectly with the Timbren Axle-Less Trailer Suspension System # ASR3500S06. This galvanized, 3,500 pound idler hub uses the needed bearings and seal to match up with the spindles on the Timbren system. The hub features a 5 on 4-1/2 inch bolt pattern and the E-Z lube-compatible grease cap will allow for easy lubrication of the bearings. The galvanized finish offers superior corrosion resistance. The bearings, races, and seal are included.
I have attached a short video demonstration on this hub that you can also check out.
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension - Standard Duty - 4" Lift - 4 Bolt Flange - 3,500 lbs
- Trailer Axles
- Rubber Spring Suspension
- Standard Grade
- No Hubs
- 3500 lbs
- Spindles Only
- Universal Fit
- Lift - 4 Inch
- Timbren
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: hanger kit
- Search Results: trailer axle
- Shop: SumoSprings Trailer Helper Springs w/ Line Relocation Bracket - Single Axle - 5K to 8K - Underslung
- Shop: SumoSprings Trailer Helper Springs w/ Line Relocation Bracket - Single Axle - 3K to 5K - Overslung
- Shop: SumoSprings Trailer Helper Springs w/ Line Relocation Bracket - Single Axle - 3K to 5K - Underslung
- Search Results: 545
- Search Results: asr3500
- Search Results: 545 hub
- Shop: Dexter Trailer Axle w/ Idler Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 72" Long - 2,000 lbs
- Shop: CE Smith U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4" Long U-Bolts - Zinc
- Shop: Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
- Shop: Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 7/8" Rear
- Article: Trailer Wiring Diagrams
- Video: Measuring To Choose The Right Trailer Axle
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Suspension Enhancement
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Q&A: Can I Use Heavier Rated Leaf Springs on Trailer Without Causing Damage
- Shop: Gooseneck Hitch
- Article: How to Measure for Trailer Hitch Drop
on Trailer Axles
Greg L.
3/1/2020
Looking to replace dexter torqflex tandem axle assembly on my Hallmark SnoLite snowmobile trailer. Being the trailer frame is boxed aluminum will the Trimbren axle with the 4inch lift work. This trailer has the tires tucked under the trailer unlike most newer ones with the tires on the outside of the trailer. Concerned my 205/75R 14 tires might not have clearance. Plus not that easy align the bolt holes while drilling from on side to the next. Is the boxed aluminum strong enough to through bolt? Manyquestions before I take on this summer project. Unsure of what degree I have right know 22.5or 45. To much snow on the ground right now. Any recommendations would be appreciated. Or just put new Dexter axles back on.