Is Hydrastar Actuator part # HBA16 Compatible with 2017 Ford F350s Factory Brake Controller

Question

Question:

Is the Hydrastar HBA-16 compatible with a 2017 Ford F350s factory brake controller?

asked by: Mark E

0

Expert Reply:

Yes, the Hydrastar Actuator part # HBA16 that you referenced is compatible with the integrated brake controller of your 2017 Ford F-350.

expert reply by: Jameson C

0

Answer 1

The OEM trailer brake controllers in some model year Ford trucks are not directly compatible with electric-over-hydraulic (EOH) trailer brake actuators like the Hydrastar #HBA16 and will require either use of adapter #HBA-CAM or an aftermarket brake…

view full answer...

Answer 2

Hello Bruce; I wasn't able to find out what kind of axle or bolt pattern you have on your 2022 ShoreLand'r YAV46TELWMS1-00 so you will need to identify it to see if these will fit. Both of these DeeMaxx Disc Brake Kits are designed to fit a…

view full answer...

Answer 3

Hi David; I honestly wouldn't choose steel brake lines for a salt water application, even if they were stainless. A better option would be the Hydrastar Hydraulic Brake Line Kit #HS496-152 or #HS496-252 with copper-nickel alloy. This has proven…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Is Hydrastar Actuator part # HBA16 Compatible with 2017 Ford F350s Factory Brake Controller

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching