Amp Draw For the MaxxAir MaxxFan #MA00-04500K

Question

Question:

What is the amp draw of the MaxxAir MaxxFan Plus 4500K vent fan?

asked by: J

1

Helpful Expert Reply:

The 900 CFM fan of the MaxxAir MaxxFan #MA00-04500K that you referenced needs to be attached to at least a 5 amp circuit. So it's max draw would be 5 amps.

expert reply by: Jameson C

1

Answer 1

I would be happy to help you. Based on the information you have given me I am going to give you the height of the Stromberg Carlson Electric Trailer Jack Item #SC63VR you referenced. This jack sits 21 1/4" above your trailer's frame. You…

view full answer...

Answer 2

The MaxxAir MaxxFan #MA00A04401K that you asked about has a maximum draw of 4-1/4 amps when it is set at it's highest setting. Since this is a 4 speed fan it will decrease about 25 percent for each setting that is one step lower. This means that…

view full answer...

Answer 3

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Amp Draw For the MaxxAir MaxxFan #MA00-04500K

Product Page this Question was Asked From

Continue Researching