Does Trailer Suspension Equalizer TREQ1304 Require Bushings
Updated 02/19/2018 | Published 02/16/2018
Products Featured in This Question
Question:
I bought and also bought center bushings from you guys but the bushing is the same exact size as the center hole so it’s impossible to bushing. My question is do the require bushings if so which ones are they?
asked by: Maurice
Expert Reply:
The large center hole on equalizer # TREQ1304 should be 7/8 inches in diameter. I checked your order and the equalizer bushings you bought were # TRBU13871. These have a 7/8 inch INNER diameter but the outer diameter is 1-1/8 inches which is why they will not fit.
You can use bushings that have an outer diameter of 7/8 inches. We have # TRBU11568 but it is 1-3/4 inches long which is 1/4 inch shorter than the width of the equalizer. It has an inner diameter of 9/16 inches.
We also have # TRBU11508 which is also 7/8 inch outer diameter and 1-3/4 inches long but with a 1/2 inch inner diameter.
Another option is to just use a 7/8 inch wet bolt, # TRFA71063, as long as the hanger for the equalizer will also accept a 7/8 inch diameter bolt. It looks like you bought some of those too so you would not need the bushings.
Product Page this Question was Asked From
Equalizer for 2" Wide Slipper Springs - 11" Long - 7/8" Center Hole
- Trailer Suspension Parts
- Standard Equalizer
- Camper
- Car Hauler
- Utility Trailer
- Slipper Springs - 2 Inch
- 11 Inch Long
- Tandem Axle
- Triple Axle
- TruRyde
more information >
Continue Researching
- Search Results: center hanger
- Search Results: standard equalizer trailer suspension parts
- Q&A: 11 Inch Long Equalizer For 2 Inch Slipper Springs & 7/8 Inch Wet Bolt
- Shop: Dexter Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 48-1/2" Axle Spacing
- Shop: Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 12" Long Equalizers
- Shop: Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 13-1/8" Long Equalizers
- Shop: Equalizer for 2" Wide Slipper Springs - 11" Long - 7/8" Center Hole
- Shop: Equalizer for 2" Wide Slipper Springs - 12" Long - 7/8" Center Hole
- Shop: Spring-Eye Bolt with Locknut for Slipper Springs - 3-1/2" Long
- Shop: Wet Equalizer Bolt with Castle Nut and Grease Zerk - 4-11/16" Long - 7/8" Diameter
- Search Results: spring eye bushings
- Video: Equalizer Bolt with Cotter Pin and Castle Nut: The Breakdown
- Search Results: double eye springs trailer leaf springs
- Video: Comprehensive Review: Spring-Eye Bolt with Locknut for Slipper Springs
- Video: Comprehensive Review: Suspension Bushing
- Search Results: spring eye bushing
- Q&A: Replacement For 11-1/2" Slipper Spring Equalizer
- Q&A: Difference Between Dexter Hub and Drums 42866UC3 & 42866UC3-EZ
- Q&A: 12 Inch Long Equalizer For 2 Inch Slipper Springs & 8,000 lb U-Bolts For Tandem Axle Trailer
- Shop: Trailer Hitch
- Search Results: equilizer shank
- Video: Complete Breakdown of the Wet Equalizer Bolt with Castle Nut and Grease Zerk
- Shop: Brake Controller
- Shop: Performance Chip Tuners
- Q&A: Installation Instructions for Equalizer for Slipper Springs
- Q&A: Recommended Hitch for 2006 Ford F-350 Towing Dump Trailer
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Wiring
on Trailer Suspension Parts
