Recommended Trailer Jack to Use with Bulldog Heavy-Duty Cast Head Coupler # BD44150WH301

Question

Question:

will BD195322 fit and bolt onto BD44150WH301 or is modification to the coupler required?

asked by: Andy

0

Expert Reply:

I do have a solution for you, however the Bulldog Square A-Frame Jack referenced in your question will not work well with the Bulldog Heavy-Duty Cast Head Coupler # BD44150WH301. This is because this particular coupler features a 2-1/4 inch diameter hole that is designed to accept round tube trailer jacks, not a square design like the Bulldog model you mentioned.

For this coupler, I instead recommend looking at the Bulldog Round A-Frame Jack # BD1550101344. This is another great 3,000 pound trailer jack from Bulldog but it features a round tube design with a 2-1/4 inch diameter, making it a perfect match for the above mentioned coupler. It has a total lift of 13 inches and a retracted bracket height of 7 inches. You can add the Detachable Footplate # PS1400700340 or Caster # PS1400750340.

I have attached a short video demonstration on this product that you can also take a look at.

expert reply by: Chris R

0

Answer 1

The Bulldog Heavy-Duty A-Frame Coupler, #BD44150WH301, does not come with the attachment bolts. I have attached two images showing the bolt pattern measurements and the bolt hole sizes. I would recommend using grade 8 bolts, but grade 5 is acceptable…

view full answer...

Answer 2

Sleeve-Lock A-Frame Trailer Coupler #CA-5296H-B is made for weld-on installation. We do have A-frame couplers that bolt on, like #BD44150WH301 and others shown on the linked page, but none of these is a sleeve lock type. Drilling the coupler to allow…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 9

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 10

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 11

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 12

We sure do Jerry and welcome back! To replace the Replacement Dexter Versa-Flex Torsion Arm Kit item #DX24FT. This replacement arm is designed for a 3,700-lb Dexter Versa-Flex axle. It's going to replace the entire arm assembly and rotor hub. It…

view full answer...

Recommended Trailer Jack to Use with Bulldog Heavy-Duty Cast Head Coupler # BD44150WH301

Featured Help Information

Miscellaneous Media

Continue Researching