Brake Assembly Recommendation for 1985 Horse Trailer with 12 inch Brake Assemblies 4 Bolt

Question

Question:

The magnets are bad they have the 4 bolt mounting pattern and 8 lug wheels. They are 12 x 2 brakes. The backing plate is offset so the 4 bolts ends are level with the backing plate. The center hub is 3 1/2” any ideas of replacement parts

asked by: Dave

0

Expert Reply:

Sounds like you have 12 inch AL KO axles and need the part # 23-105-106-09. If the upper bolts are slightly wider than the lower ones that is the correct kit you'd need.

expert reply by: Jameson C

0

Answer 1

Based on the picture you provided it does look like your 1985 Hale Horse Trailer uses the AL-KO 4-bolt pattern and would require you to use the Dexter Electric Brake Kit #23-105-106-09. This kit is designed for 6000lb axles and measures 12" x…

view full answer...

Answer 2

We have a set of brake assemblies fit to replace your 12 inch x 2 inch AL-KO electric brakes. The Dexter #23-105-09 left-hand side, #23-106-09 right-hand side. These brake assemblies are rated for 6,000 pounds per pair like your axle and have the…

view full answer...

Answer 3

It looks like the studs in your brake assembly are closer together (center to center) at the bottom. If the center to center bolt spacing matches the photo I've provided, then the #23-105-09 you'd looked at would be the correct replacement…

view full answer...

Answer 4

You'll need to do some quick measuring of your backing plate/brake flange to see if you can use the 6,000 lb Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Left Hand #23-105-09. I have added photos below that I hope will…

view full answer...

Answer 5

The brakes in the picture look like they have the offset 4 bolt pattern that Hayes/AL-KO brakes use. On that bolt pattern the top two holes are spaced further apart than the bottom 2 holes. If they are 12 x 2 inch brakes then we have some with that…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Brake Assembly Recommendation for 1985 Horse Trailer with 12 inch Brake Assemblies 4 Bolt

Product Page this Question was Asked From

Continue Researching