Installing Titan T1607500 Surge Brake Actuator As Replacement For Titan Model 10 Actuator

Question

Question:

Since my existing Titan model 10 actuator is welded on, is it possible to purchase everything except the outer sleeve portion meaning the portion that welds on as an assembly and avoid having to cut if off and re-weld the new one on?

asked by: Trevor M

0

Expert Reply:

Unfortunately you will have to remove everything in order to properly complete the weld install of the Titan Brake Actuator, Item # T1607500.

Please contact me if you have any other questions.

expert reply by: Brint H

0

Answer 1

We've checked the part number you gave us before and the replacement for it is the part #T4750820 which is for disc brakes. This one does come with a reverse lock out solenoid. If it has rust all over it I'd consider just replacing the entire…

view full answer...

Answer 2

We have what you need. The Dico 17550 refers to a 2-5/16" ball replacement not the actual actuator. For the actuator and coupler use the Titan Brake Actuator part #T1607500 will get you back up and running. This is for drum brakes and offers a…

view full answer...

Answer 3

Yes, for just the inner slide assembly of the Titan Model 10 actuator part #T1607500 you would want the part #T1608400317.

view full answer...

Answer 4

Thanks for the photos of your trailer's actuator! They were very helpful in answering your questions. Based on the photos, it appears that you have a Titan Model 10 Actuator #T1607500. For a Model 10 actuator, the #DX66FR that you referenced is…

view full answer...

Answer 5

The DICO Model 10 that you have is essentially the exact same thing as the Titan Brake Actuator #T1607500 that you referenced. This would be an exact replacement.

view full answer...

Answer 6

The replacement Titan actuator for your Model 10 with part number 3241639 is listed on our site as the Titan Zinc-Plated Brake Actuator w/ Drop, Electric Lockout #T4750620. My contact at Titan confirmed this.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Installing Titan T1607500 Surge Brake Actuator As Replacement For Titan Model 10 Actuator

Product Page this Question was Asked From

Continue Researching