Will the Demco Solenoid Kit # DM5837 Fit Demco Hydraulic Brake Actuator # DM8759812

Question

Question:

Does this reverse solenoid DM5837 Work on this hitch DM8759812 The solenoid doesn’t list that model number hitch or is there another one that fits it? I wouldn’t think the master cylinder setups are different between the other demco hitches that why I need more info.

asked by: Austin E

1

Helpful Expert Reply:

Since the Demco Hydraulic Brake Actuator # DM8759812 is a DA91 actuator the Reverse Lockout Solenoid Kit # DM5837 will fit. I confirmed this with my contact at Demco.

expert reply by: Jon G

1

Answer 1

Yes! The manual reverse lockout kit you are looking for is the #DM5939 for D91 Demco Hydraulic Trailer Brake Actuators. I have linked the product and installation instructions to this page for your convenience.

view full answer...

Answer 2

You can add a Manual Reverse Lockout Kit #DM5939 or Electric Reverse Lockout Solenoid Kit #DM5837 to the Demco Hydraulic Brake Actuator #DM8509612 to get the DA91 surge coupler with a reverse lockout.

view full answer...

Answer 3

I do have a solution, but we do not have a bolt-on actuator for a 4" wide trailer tongue. What you can use is the #DM8759922 along with #DM12688-95. This brake actuator can be welded on top of the trailer tongue. You will need to take it to a…

view full answer...

Answer 4

I recommend replacing your obsolete Atwood surge coupler with the Demco Hydraulic Brake Actuator #DM8509612. This coupler is rated for trailers up to 7,000lbs and connects to the vehicle with a 4" drop coupler accepting a 2" hitch ball so…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…

view full answer...

Answer 12

Hello James, thanks for reaching out. Both the kits you mentioned, the Hydrastar #HYD22FR and #HYD42FR are complete conversion kits for standard 3,500 lb axles. The difference is the calipers included with each kit. The #HYD22FR has stainless steel…

view full answer...

Will the Demco Solenoid Kit # DM5837 Fit Demco Hydraulic Brake Actuator # DM8759812

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching