Replacement Bolt-On Fulton Trailer Jack

Question

Question:

I need to replace a Fulton jack on a boat trailer. It has a center bolt, which bolts to a welded bracket on the trailer. Which trailer jacks do you offer that will fit this application?

asked by: Dan O

0

Expert Reply:

Thank you for the photo it was helpful in determining what you need. The replacement would be the Fulton Bolt-Thru Swivel Marine Jack # FXP10W0301 which has a bolt-through mount, 1,200 lb lift capacity and has bracket heights of 12-3/4" retracted and 22-3/4" extended. I've added a link to a video review of this jack for you to look at.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Thanks for the picture, it looks like you have the Fulton F2 Swing-Up, Wide-Track Trailer Jack #F1413040134 in which you'd need the Wide-Track Wheel Assembly for Fulton F2 Adjustable A-Frame Jack #F500266 for a replacement.

view full answer...

Answer 2

The jack won't fit unfortunately since the max frame width it can fit is 3 inches but you could pretty easily go with a weld on jack like the Fulton #FXP10W0301.

view full answer...

Answer 3

Shelby jacks are no longer in production. If the welded mount had a bolt-thru design, then I recommend checking the pin hole dimensions for compatibility. The bolt hole centers are 3 inches apart on the Jack Mounting Bracket for Fulton Marine Jack…

view full answer...

Answer 4

We offer weld-on and bolt-on trailer jacks that are similar to the Shelby 5764A jack you wish to replace but the jacks we offer are not exact replacements. We do have a jack that has a mounting plate similar to the Shelby mounting plate., It is part…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Bolt-On Fulton Trailer Jack

Featured Help Information

Miscellaneous Media

Continue Researching