Correct Grease Seal for Idler Hub Assembly TA88545-2

Question

Question:

I need a grease seal for a 1.25inch inner OD and a 2 inch outer OD. The seal needs to fit in the following hub assembly TA88545-2 I purchased from E-Trailer.

asked by: Adam A

0

Expert Reply:

The proper grease seal for idler hub assembly # TA88545-2 is the 10-60 seal, which is # RG06-020.

expert reply by: Kyle S

0

Answer 1

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 2

Yes, the Trailer Idler Hub Assemblies #TA88545-2 are two 5 on 4-1/2" bolt pattern idler hubs that will fit the CE Smith Trailer Axle Beam with EZ-Lube Standard Spindles #CE33201GA. These will allow for you to mount a 15" wheel and tire like…

view full answer...

Answer 3

The Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 #TA88545-2 uses inner and outer bearing #L44649, which has a 1.063 inch inner diameter and does fit what is commonly referred to as a 1 inch straight spindle.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 7

Based on the number and dimensions you listed the correct grease seal you need is the part #RG06-020 as this cross references to what you have and matches the dimensions.

view full answer...

Answer 8

Hey Bruce, it sounds like you might have some older seals, perhaps Transcom seals with the 1.983" OD. We do have one seal, the #10-9 seal, which has proven to be a suitable replacement for these seals. This is a double lip seal with a 1.5"…

view full answer...

Answer 9

You are correct, a double lip seal is better than a single lip. All things being equal I always recommend a double lip when available. Especially when the application is a boat trailer that will get submerged in water. The other difference between…

view full answer...

Answer 10

Hey Donny, The Furrion Chill Cube #FR99TD doesn’t use a separate freeze sensor like the older RV AC units you might be used to installing. There’s no probe to mount, no extra wiring, and nothing missing from the installation steps. Everything is…

view full answer...

Answer 11

The Titan Chain Sliding Lashing Winch for Flatbed Truck or Trailer - 6,000 lbs #TCLR912 will work with straps like the Titan Chain Strap for Truck and Trailer Winch - Flat Hook - 4" x 30' - 5,400 lbs - Blue #TCLR430-1-33. This strap is what…

view full answer...

Answer 12

Sure, you can weld the low-profile Titan Chain Lashing Winch for Flatbed Truck or Trailer #TCLR860 to the bottom of your flatbed truck. The only difference between this winch and the "bottom mount" Titan Chain Lashing Winch for Flatbed…

view full answer...

Correct Grease Seal for Idler Hub Assembly TA88545-2

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching