Replacement Hub/Drum Assembly Needed For A Older Boat Trailer
Published 01/13/2025 >
Products Featured in This Question
Question:
I need a brake drum hub for an older boat trailer. 10 drum 5 bolt x 4.5 inner race 2.442OD inner brg 1.249 ID outer race 1.941OD outer brg .75 ID depth of hub 5 3/8 Can you help Thanks
asked by: Dennis M
Expert Reply:
Hey Dennis,
Based on the dimensions you provided it looks like your hub uses bearings # TMK36FR (LM11949) and # LM67048. The Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 # DX22XR is the only option we currently offer that uses these bearings and it unfortunately isn't a hub/drum assembly. You'll most likely need to replace the axle at this point to get a more common spindle and hub/drum.
If you want to go that route then you'll want to measure the spacing between the hub faces and spring seats (see diagram below). If you want some help or find that your measurements don't match up to anything we offer then you can call our customer service department at (800) 298-8924 and they can custom order the axle with you.
Product Page this Question was Asked From
Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Drum
- Pre-Greased
- Standard
- L68149 / L44649
- Standard Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Continue Researching
- Search Results: trailer safety chains
- Search Results: license plate trailer lights
- Search Results: identification light bar
- Article: Trailer Lighting Requirements
- Video: Checking Out the Optronics LED Clearance or Side Marker Light w/ Reflector
- Video: Complete Breakdown of the Identification Light Bar for Trailers over 80" Wide
- Video: Comprehensive Review: LED Clearance or Side Marker Light with Reflector
- Video: LED Identification Light Bar for Trailers over 80" Wide: The Breakdown
- Video: BulletProof Hitches 5/16" Safety Chains with Clevis Hooks Feature Review
- Video: LED Identification Light Bar for Trailers over 80" Wide Review
- Q&A: Ratings for 5/16" and 3/8" Safety Chains
- Search Results: identification light
- Search Results: red reflector
- Shop: Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2
- Shop: Optronics LED Clearance Light - 3/4" Round - Yellow - 12V-24V
- Q&A: Looking for Safety Chains that Fit 2020 1995 Lance Trailer
- Q&A: Do you Carry a LED Side Marker Light Like Part Number MC35AEB
- Q&A: What Is Max Bolt Diameter that Could Fit Through CE Smith Chain part # CES42QR
- Q&A: How to Choose Correct Capacity for Trailer Safety Chains
- Video: The Low-Down on the Peterson LED Clearance or Side Marker Trailer Light w/ Reflector
- Shop: Optronics LED Side Marker or Clearance Light w/ Reflector for Carry-On Trailers - 3 Diodes - Amber
- Shop: Clearance or Side Marker Trailer Light w/ Reflex Reflector - Rectangle - Amber Lens
- Shop: LED Clearance or Side Marker Light with Reflector - Submersible - 2 Diodes - Rectangle - Red Lens
- Shop: Optronics Trailer Tail Light - Stop, Turn, Tail - Round - Red Lens - Passenger Side
- Shop: Optronics LED Clearance or Side Marker Light w/ Reflector - 2 Diodes - Rectangle - Amber Lens
- Search Results: 10~19 seal
- Search Results: 10~19 grease seal
- Q&A: What is the Difference Between Over 80 inch and Under 80 inch Trailer Tail Lights
- Q&A: Does Optronics Offer The Marker/Clearance Light # MCL35A32G With a Red Lens?
- Article: Most Popular Wheel Bearings



Dennis
1/13/2025
Thanks, I was afraid of that being the case. I will see about getting that info together.