Additional Base Plate for the Rack'em Manufacturing Removable Wheel Chock Part # RA-17

Question

Question:

I would like to buy a RA-17 wheel chock and an additional base plate. What is the part # for a extra base plate

asked by: David H

0

Expert Reply:

The part number for the base plate used in the Rack'em Manufacturing Removable Wheel Chock part # RA-17 is the Steel Replacement Base part # RA-17B. Please keep in mind that this is the base plate only and you will need to supply your own hardware in order to secure the base plate to your trailer.

expert reply by: Conner L

0

Answer 1

Both the Dexter Electric Trailer Brake Kit #23-47-48 and the Electric Trailer Brake Kit #AKEBRK-2 are excellent options to replace the brake assemblies on your 2009 Palomino Pony pop-up camper. A lot of the Dexter Axle kit price comes from the name…

view full answer...

Answer 2

The etrailer 3,500lb Trailer Axle #e52GR you were looking at is made for us by Axletek.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Additional Base Plate for the Rack'em Manufacturing Removable Wheel Chock Part # RA-17

Products Featured in This Question

Continue Researching