When Using Bearing Buddy Bearing Protectors Do I Need To Repack Bearings Periodically?

Question

Question:

Does having a Bearing Buddy installed negate the need to take apart the wheel hub and repack the bearings with fresh grease periodically?

asked by: Jesse

0

Expert Reply:

When you use the Bearing Buddy Bearing Protectors like # BB2441, so you do not need to take apart the wheel hub and repack the bearings. The Bearing Buddy Protectors have a spring loaded seal that keeps the moisture and debris out of the bearings. This pressurized grease will maintain bearing function as long as the seal on the hub stays functional. If this seal is broken, I recommend inspecting and repacking good bearings when you replace the seal. As you maintain the grease in the Bearing Buddy, it continues to fill the bore, so your bearings and spindle stay properly lubricated for proper function.

expert reply by: Jason S

0

Mark G.

6/10/2020

How often do I need to grease bearing buddys?

Jacob H.

6/12/2020

We recommend greasing your hubs on your trailer about every 12,000 miles under normal conditions. If you are hauling heavy loads often then you may want to so it sooner.

Mark G.

6/12/2020

Thank you!What I mean is how often should I shoot grease into the bearing buddy as a preventative maintenance function?After so many trips,once a month etc.

Chris R.

6/16/2020

Assuming the seal is in good condition (grease isn't escaping) there really shouldn't be a need to add more grease throughout the year. You're safe to follow the general guideline of once a year or 12,000 miles.

See All (5) Replies to Mark G. ∨

Mark G.

6/20/2020

Thank you very much!

Chris R.

6/23/2020

No problem at all!

Rick B.

7/10/2024

Can you use Bearing Buddies on a boat trailer with drum brakes? Thanks, RB

Bud M.

7/10/2024

@RickB Yes, Bearing Buddy bearing protectors can be used on a boat trailer with drum brakes. I do recommend using their matching grease seal kit as it is capable of the higher grease pressures you get with a Bearing Buddy. This helps prevent grease from getting into the brake assembly.

Steve T.

7/17/2024

@BudM I just had my wheel bearings replaced on my single axle boat trailer and Bearing Buddies installed. The tech recommended that I add grease every time before I put it in the water after any trip of decent distance. Don't I run the risk of blowing out a rear seal doing this? If the seals are good, where is all the original grease going to make room for more? We probably tow it enough to get the bearing warm 5 or 6 times a year, and in 15 years of boating, I've never seen anyone else doing it. Is he being too cautious? Am I being to reckless not doing it? Thanks, ST

Bud M.

7/17/2024

@SteveT If you used the auto check style bearing buddies you can simply check the pressure cap to determine when you need to add more grease. Typically I recommend checking them a few times a year depending on use. As grease doesn't just disappear you would notice if it were come out of the hub.

Answer 1

For as trashed as those brake assemblies are I am impressed with how spotless that spindle is! Based on the bearing numbers you mentioned you have a #84 spindle and the hub part #AKHD-545-35-G-K is correct. Since this its galvanized it's a really…

view full answer...

Answer 2

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 3

The Dexter #T3584F-EZ-8974 axle beam weighs 65 pounds. I have attached a review video.

view full answer...

Answer 4

Bearing Buddy pumps grease into the center of the hub all the way back to the grease seal. A double lip seal should be used to prevent grease from blowing out the seal when added. When the hub and seals and bearings are first assembled, they should…

view full answer...

Answer 5

Axles rated for 6,000 to 7,200 pounds usually will have 3 inch diameters. But it is possible for 5,200 pound axles or even 3,500 pound axles to have a 3 inch diameter axle. You could err on the side of caution and say each axle is rated for 3.5K for…

view full answer...

Answer 6

There is not a video available as of this writing (June 2019) but there is a clamp just forward of the muffler that needs to be loosened so you can remove the rear portion of the exhaust from your 2019 Jeep Cherokee to install the Curt Trailer Hitch…

view full answer...

Answer 7

The best option would be for you to use a hitch on your trailer, and Curt #13703 would be a great choice and will fit your travel trailer so long as it has a box frame, I-beam frame or C-channel frame and is between 22" and 72" wide. This…

view full answer...

Answer 8

No, you do not! Bearing Buddy Bearing Protectors like item #BB1781 grease both the inner and out bearing so you don't need to worry about taking your hub apart to repack the inner bearings.

view full answer...

Answer 9

Yes! You can use Bearing Buddies on anything as long as you use the right size and as long as the axles are not EZ Lube axles with the grease fittings on the ends of the spindles. If your outer bearings are L44643, L44649, or L44640 then you can use…

view full answer...

Answer 10

The Peterson Trailer Tail Light #V457L that you referenced is designed to ground through the mounting hardware which means that a bolt runs through the base which is attached to the ground circuit of the light and when it contacts the metal frame of…

view full answer...

Answer 11

Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?

view full answer...

Answer 12

Hi Steve! For salt water applications, I always recommend Aluminum wheels. Galvanized steel will hold up better than raw or painted steel, but aluminum is king in this regard. You still want to clean them off after they get all salty as aluminum does…

view full answer...

When Using Bearing Buddy Bearing Protectors Do I Need To Repack Bearings Periodically?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching