What is the Rear Sway Bar Size of a 2002 Ford F-53

Question

Question:

what size is the rear sway bar on our 2002 Ford F53 24/26k chassis?

asked by: Jared S

0

Expert Reply:

The only way to know if the Roadmaster Polyurethane Bushing Kit for 1-1/2" Diameter, Factory Rear Anti-Sway Bar # RM-4139-125 will fit the rear sway bar on your 2002 Ford F-53 chassis is for you to measure them using a Digital Caliper, like part # PTW80157.

Since different RV manufacturers will install their own preferred equipment on any given chassis you have a much more guarantee of a fit if you can check the measurement physically.

expert reply by: Jon G

0

Answer 1

Hello Sam, Thanks for writing in! I'm glad you wrote in because I was able to verify the sway bar on your motorhome. I show that your 2000 Itasca Suncruiser 32V with the Ford F-53 chassis has the Roadmaster Rear Anti-Sway Bar - 1-1/2"…

view full answer...

Answer 2

In order to replace just the factory anti-sway bar bushings on a Ford F-53 Chassis you have a few options which will be based on the location of the anti-sway bar (front/rear) and the gross vehicle weight rating of the coach (15,700 lbs, 16,000 lbs…

view full answer...

Answer 3

I did some checking on your 1999 Fleetwood Bounder 34v and it appears that it was built on the Ford F53 chassis which is a common one for Class A RVs. There is a bushing upgrade kit for the rear anti-sway bar and it is #RM-4139-125. The single…

view full answer...

Answer 4

Some of the bushings on the Roadmaster #RM-4139-125 will need to be pressed in, but it is not overly difficult. I included an install video we have of a similar Roadmaster kit that will show how this needs to be done.

view full answer...

Answer 5

I will start off by saying that the Replacement Bushing #RM-205381-00 is the direct replacement for the Roadmaster Polyurethane Bushing Kit for 1-3/8" Diameter, Factory Rear Anti-Sway #RM-4139-300. To further that, the Replacement Polyurethane…

view full answer...

Answer 6

Thank you for info on your RV. Based on that the correct bushing replacement you need is the Roadmaster part #RM-4139-300 that you referenced. You do have a 1-3/8 inch diameter sway bar.

view full answer...

Answer 7

We do have replacement bushing and mount kits that fit your 2007 Fleetwood Bounder 33R for the rear sway bar but it depends on what the diameter of your factory bar is. If the diameter is 1-3/8 inch you'd want the part #RM-4139-300 or if it's…

view full answer...

Answer 8

Since the bolts that come with the Roadmaster Polyurethane Bushing Kit #RM-4139-125 are designed to attach to threaded parts of the vehicle suspension nuts are not included or needed. Check out the install video I attached for more info on how it…

view full answer...

Answer 9

For your Roadmaster Front Anti-Sway Bar #RM-1139-148 on your 2014 Ford F-53, the correct replacement bracket is the: -Replacement Bushing Clamp for Roadmaster Front Anti Sway Bar #RM64MR. This bracket will not fit the rear sway bars #RM-1139-146, for…

view full answer...

Answer 10

I am not sure what is wrong with the links but I have included a picture of the instructions for the rear, #RM-4139-125, and for the front, #RM-4139-127, for your RV built on the 1997 Ford F-53. V8 chassis. The rear is on the top and the front is on…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

What is the Rear Sway Bar Size of a 2002 Ford F-53

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching