Comparing The Timbren Axle-Less Trailer Suspension System To The FlexiRide Half Torsion Axle System
Updated 06/01/2017 | Published 05/31/2017
Question:
Struggle to make a decision.I have a offroad overland trailer that carries all or camping gear and rooftop top. it is pulled behind a lifted Jeep JKU. The current clearance from the bottom of the frame rail on the trailer is 19.5 inches. I plan to remove the axle and leaf springs and go to an axle-less setup but I dont want to lose any ground clearance. I am not sure whether I should get the Timbren A12WS545 or the Flexiride FF-140B-2. I was hoping I could get some expert opinion. I know you dont stock the Flexiride, but you are the experts.
asked by: Kyle
Expert Reply:
For an off road overland trailer, I recommend you go with the Timbren Axle-Less Trailer Suspension System with Hubs - 5 on 4-1/2 - Off-Road Tires - 1,200 lbs # A12WS545 and not just because we carry them...as I know seems like a conflict of interest. The Flexiride system even with a 1,400 lb capacity is not made for off road and the suspension is a torsion system with rubber cartridge on each side. The Timbren system uses more of a jounce style bumper that the company is known for regarding vehicle suspension enhancement. This compression jounce spring will give you far more durability than a torsion system by taking the brunt of the impact. You can see by the design that this system is designed to resist and absorb impact versus just absorb it. This system can also be mounted to your trailer using a 2 inch square rod between the springs in the included holes if a cross member of the trailer is not present and will still give you greater ground clearance and stability.
Please let me know if you have further questions. I've attached a video of this system for you.
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: st225/75r15
- Shop: Trailer Hitch
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 4" Lift - 4 Bolt - 2.2K
- Shop: Timbren Axle-Less Trailer Suspension w/ Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 2K
- Shop: Redarc In-Vehicle BCDC Trailer Battery Charger - Dual Input - DC to DC - 12V - 12 Amp / Solar 40 Amp
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: Electric Trailer Brakes: How They Work & What to Buy
- Video: etrailer Trailer Brake Controller 7-Way RV Upgrade Kit Installation - 2018 Subaru Outback Wagon
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Video: Trailer Wiring Harness Installation - 2017 Subaru Outback Wagon
- Video: Installation: Curt Trailer Hitch Receiver on a 2017 Subaru Outback Wagon
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Shop: Trailer Wiring
- Shop: Brake Controller
- Shop: Towing Kit w/ Ball Mount and Trailer Wiring for Stealth Hitches Hidden Rack Receiver - 2" Ball
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Powerbuilt Trim Pad Remover
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: Availability Of Replacement Rubber Aeon Springs For Timbren Axle-Less Suspension
- Q&A: 7-Way Mounting Bracket for Use with ETBC7L and Curt Echo Mobile Brake Controller
- Search Results: half torsion axle
- Q&A: Does it Matter Which Trailer Brake Assembly is Right and Which is Left
- Q&A: Should Trailer Mounted Batteries Be Grounded to Trailer Frame
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Video: Easily Install Your Curt Class III Trailer Hitch - 2024 Toyota RAV4
- Q&A: Diagram Showing How Trailer Brakes are Wired
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Q&A: Where Should Trailer Brake Assemblies be Grounded?
- Search Results: trailer hitch
on Trailer Axles
