Mounting Hole Dimensions Of The Dutton-Lainson Hand Winch Part # DL15440

Question

Question:

are the mounting holes the same on a DL15440 as they are on a shelby model 5470A

asked by: Michael N

0

Expert Reply:

I do have the mounting location dimensions for the Dutton-Lainson Hand Winch part # DL15440 however, the Shelby Hand Winch part # 5470A is no longer available and as of October of 2016, SHELBY has gone out of business. I called my representative at Dutton-Lainson and unfortunately they were not able to provide me with compatibility information for Shelby winches.

The mounting hole locations for the Dutton-Lainson Hand Winch are as follows. The distance from the upper most hole to bottom hole is 4-7/8". The second most lower hole is 1" above the the lowest hole. The large oval shaped holes located at the bottom left and right hand corner are 3-1/4" from the two middle mounting holes. These two middle holes are 3" apart.

I have attached a picture of these dimensions for a more exact illustration.

expert reply by: Conner L

0

click to enlarge

Answer 1

The base on 2-Speed Boat Trailer Winch #315-W2500D measures 5-3/4 inches wide by 7-1/8 inches long. This is a very standard size and bolt pattern so it should fit on your trailer easily. I attached a review video for this for you to check out as…

view full answer...

Answer 2

The bolt hole spacing as well as the bolt hole pattern is different when you compare the #DL14627 (which is the 1802A) to the #DL15440 (3200A). The overall dimensions differ as well. I am attaching some pictures showing the bolt hole measurements as…

view full answer...

Answer 3

The 2-Speed Boat Trailer Winch part #315-W3200D is an excellent upgraded 3,200 lb winch for a boat trailer. In regards to mounting, not all winches use the same pattern so you'd need to compare the dimensions in the photo below to what you have…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…

view full answer...

Answer 7

Thanks for reaching out Brennan, Since we no longer carry Fulton winches, the closest replacement we offer is the Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 2,500 lbs #DL14825. It's comparable to the capacity and…

view full answer...

Answer 8

Generally when picking out a winch for a boat trailer the ratio is 2 to 1 meaning you would need a winch with roughly half the capacity as the weight of the boat. With good rollers and a short winching distance the ratio increases to 3 to 1, but with…

view full answer...

Answer 9

When it comes to choosing a winch for a boat trailer, there are a few general rules we can use. The boat-size-to-winch capacity is generally 2 to 1. With good rollers and short winching distances, the ration can increase to 3 to 1 and with wooden…

view full answer...

Answer 10

Yes, Replacement Cap Kit for HappiJac Manual Truck Camper Jacks #LC183332 is the correct kit. This is for your Replacement Jack #LC736514 (4220) or the complete setup HappiJac Manual Truck Camper Jack System - 34-1/2" Lift - 8,800 lbs…

view full answer...

Answer 11

When using 3/8 inch cable, the hand winch we have available with the largest drum capacity is with the Dutton-Lainson Hand Winch #DL15440. This can handle up to 30 feet of 3/8 inch cable. Since you are looking for a much longer length, I recommend…

view full answer...

Answer 12

We don't carry the Shelby 5408 winch, but from what I see they are the same mounting holes as the Dutton-Lainson Hand Winch with TUFFPLATE Finish, Two Speed with Direct Drive - 3,200 lbs #DL15440. I've attached a picture of those measurements…

view full answer...

Mounting Hole Dimensions Of The Dutton-Lainson Hand Winch Part # DL15440

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching