Should Pipe Sealant be Used When Installation Propane Tank 1/4 MPT Pigtail

Question

Question:

When installing a 1/4inch MPT propane tank pigtail is it necessary to use a thread sealant on the regulator end of the pigtail?

asked by: Russ

1

Helpful Expert Reply:

Yes you should use some kind of sealant on threaded fittings whether it is the tape or pipe dope.

Using the white Teflon tape will work well on installing the propane pigtail top the LP regulator. Just wrap the tape on the threads only.

expert reply by: Jared P

1

Answer 1

There are different options depending on what style connector you have. I have included an option for both an NPT and MIF. You would just want to check what style is on your hose to ensure you get the correct hose. NPT MB Sturgis Propane Hose w/ Back…

view full answer...

Answer 2

Thanks for the photos! Yes, the MB Sturgis Propane Pigtail w/ Back Check #100575-12-MBS has the connections needed for both the regulator and the propane tank on your 2021 Grand Design Imagine 22MLE travel trailer. If you wanted to get a pigtail…

view full answer...

Answer 3

We do have hoses which may work for you. The MB Sturgis Propane Pigtail #100833-24 is a type 1 cylinder connection with a 1/4" male inverted flare. This is a 2 foot hose, though we also have a 15" hose #100833-15 and 1 foot hose…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Should Pipe Sealant be Used When Installation Propane Tank 1/4 MPT Pigtail

Product Page this Question was Asked From

Continue Researching