Time Required to Install Blue Ox Base Plate Kit BX2261

Question

Question:

How long should a BX2261 base plate and accompanying wire kit take to install in hours. What is the suggested time estimated by Blue Ox? Thank you!

asked by: Frank O

0

Expert Reply:

For a first-time base plate installer we estimate that the total time required to mount the Blue Ox Base Plate Kit # BX2261 to be a good 5 to 6 hours (half a day, let's call it). Our installers who have the benefit of having done this many times typically complete a base plate install in 2 or 3 hours.

expert reply by: Adam R

0

Answer 1

There is a suspension enhancement option for your 2021 Entegra Vision XL built on a Ford F-53 chassis, but I verified with the manufacturer that the steering stabilizer only fits if you have at least a 24,000 lb GVWR. You're not out of luck…

view full answer...

Answer 2

GM states in the owner's manual that to recreationally tow the vehicle, the negative battery cable must be disconnected. The owner's manual doesn't list a specific reason, it only states that failure to do so could damage the vehicle. The…

view full answer...

Answer 3

It sounds to me like you're experiencing vehicle sway on your RV. To remedy this, I recommend installing a steering stabilizer like #RM82RR, and you can use the rear anti-sway bar like #RM83ZR to combat body roll. If you let me know what RV you…

view full answer...

Answer 4

Your 2022 Entegra Vision XL 34G is built on the Ford F53 chassis. There is not currently a steering stabilizer available for this. However, we do have suspension enhancements available that can improve your ride and drivability. I highly recommend…

view full answer...

Answer 5

The mounting plate for the Roadmaster Rear Anti-Sway Bar Item #RM-1139-149 will be attached to the U-bolts so you'll be able to look at the U-bolts and see if there's going to be enough to threads to place the plate on and retighten the nuts.…

view full answer...

Answer 6

Some of the bushings on the Roadmaster #RM-4139-125 will need to be pressed in, but it is not overly difficult. I included an install video we have of a similar Roadmaster kit that will show how this needs to be done.

view full answer...

Answer 7

To replace/upgrade the bushings on the rear factory sway bar of your 2009 Class A Newmar Canyon Star RV you need one of the following Roadmaster kits based on the diameter of your factory sway bar: - 1-3/8" Diameter #RM-4139-300 - 1-1/2"…

view full answer...

Answer 8

I recommend having your suspension checked out to make sure there are no issues, but if everything is fine, suspension enhancement springs would help level your Itasca. I could not guarantee this will "fix" your lean but the SumoSprings…

view full answer...

Answer 9

Manufacturers do not really give a set amount of time that it takes to install a base plate kit on a 2007 Jeep Wrangler because there a lot of variables involved when installing a base plate. I have asked our installers how long it normally takes to…

view full answer...

Answer 10

I would be happy to gather a list of parts to help you flat tow your 2023 Jeep Wrangler 4xe. I have listed the ones you will need below and included any installation videos we may have: Tow Bar and Safety Chains - Roadmaster Falcon 2 Tow Bar item…

view full answer...

Answer 11

To flat tow your 2021 Jeep Wrangler Unlimited 4Xe Rubicon Hybrid you will need a tow bar, base plate, tow bar wiring kit, braking system, and safety cables. I have the following recommendations for you listed below: Tow Bar: Roadmaster Nighthawk All…

view full answer...

Answer 12

The Alpha 2 is indeed an updated version. The difference between the original Blue Ox Alpha and the #BX7380 Alpha 2 tow bar is that the Alpha 2 has non-binding latches, while the original Alpha did not. Non-binding latches, are just that, they easily…

view full answer...

Time Required to Install Blue Ox Base Plate Kit BX2261

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching