Does The Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler # CG Allow For Height Adjustment

Question

Question:

will this coupler allow height adjustment up and down like other couplers?

asked by: Lyndell

0

Expert Reply:

The Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler, part # CG, will slide up in the 4 inch inner diameter tube that is on the trailer. It can be adjusted for height by using the set screws on the gooseneck trailer tube.

expert reply by: Jeff D

0

Answer 1

The Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler part #CG is designed to be used with set screws, we cannot recommend you drill to use a pin. That said, it will still work on an inner tube with pre-drilled holes for the pins so there…

view full answer...

Answer 2

Hello Kristen, The CG Convert-A-Ball Multi-Cushioned Gooseneck Coupler #CG is your best option to replace the inner tube on your older Bulldog gooseneck hitch. What makes it so great is that it doesn’t need a load-bearing pin to work. Since your…

view full answer...

Answer 3

The Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler #CG is designed to work with the single set screw. The screw will press on the inner tube. You will not have a problem as long as you are not exceeding the towing capacity of 30,000 lbs and…

view full answer...

Answer 4

Hello Carolyn, On the Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler - Round - 30,000 lbs #CG, from the center of the ball to the farthest corner of the little red handle is 6-3/4 inches, so the recessed box needs to be 14 inches square and…

view full answer...

Answer 5

The Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler #CG does only allow for up to 3/4" so while this will help with road shock it does not help as much with the trailer bounce. Depending on your LQ horse trailer you would be able help…

view full answer...

Answer 6

The most common repair for a gooseneck coupler is replacing the inner tube so if this is what you are looking for then we do have options for you. For this, the Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler part #CG would be an excellent…

view full answer...

Answer 7

Ford and Ram factory gooseneck balls that have a plastic tab on the top, like part # RP19311, are not recommended for use with the Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler #CG because the steel surface inside the coupler can chew up…

view full answer...

Answer 8

I spoke with my contact at Convert-A-Ball about the pin weight capacity of their CG Cushioned Gooseneck Coupler. They list a 30,000 lb weight capacity for the coupler and a 4,000 lbs tongue, or pin weight. Since your 2400 lb pin weight isn't even…

view full answer...

Answer 9

I attached a couple pictures to the right that have the installation instructions for the Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter #CAB-C5G.

view full answer...

Answer 10

The Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler - Round - 30,000 lbs #CG doesn't have a specific torque spec because it is just the inner sleeve. The set bolt torque spec you need would be based on the outer sleeve with the bolts.…

view full answer...

Answer 11

We do have some options available that are a bit longer than the Bulldog BX1 Gooseneck Coupler Inner Tube #BD1289050300. The Bulldog BX1 Gooseneck Coupler Inner Tube #BD1289020300 has the same diameter and hitch ball spec and it has an overall length…

view full answer...

Answer 12

The Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler #CG is designed to normally be used with a set screw that pressed onto the inner tube basically. If you wanted to drill a hole that is properly sized for your current set screw that passes…

view full answer...

Does The Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler # CG Allow For Height Adjustment

Product Page this Question was Asked From

Continue Researching