Needing a Bearing Kit for a Lippert 3,500 Lbs Lippert Axle

Question

Question:

Just wanted to verify 3500lb lippert axle 126627 would use bearing kit bk2-100 Thanks

asked by: Steve H

0

Expert Reply:

According to Lippert, the items in # BK2-100 bearing kit are the correct parts needed to replace the bearings on one hub of your Lippert axle.

I recommend using the LubriMatic Disc/Drum Brake and Wheel Bearing Grease # L11465 when packing the wheel bearings on your axle.

expert reply by: Jared P

0

Answer 1

Hey thanks for reaching out, Robert. Your Dexter P-15 model SLR 3,500 lb axle does use the standard bearing combination for a 3,500 lb axle. I was able to confirm this with Dexter. So, you have #L68149 for the inner bearing and #L44649 for the outer…

view full answer...

Answer 2

I reached out to Bear and they were able to confirm that your 3,500lb axles use a #84 spindle. This will allow you to use the Hub Bearing Kit #BK2-100 on each of your axle hubs. The kit includes new inner and outer bearings and races, a grease seal,…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Needing a Bearing Kit for a Lippert 3,500 Lbs Lippert Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching