Replacement Wheel Cylinder For Dexter 12-Inch Hydraulic Drum Brake Assembly

Question

Question:

What is the appropriate replacement wheel cylinder for a 023-342-00 brake assembly? Thanks

asked by: Dan M

0

Expert Reply:

The replacement wheel cylinder that will work with your Dexter # 23-342 left hand brake assembly is part # AKBRKR-H7-L-CR.

If you need a replacement wheel cylinder for the right hand side you need part # AKBRKR-H7-R-CR.

expert reply by: Jeffrey L

0

Answer 1

Trailer hub and drum assembly #8-201-5 does match your bearings. I am fairly certain you have 5,200 pound axles and not 3500 pound axles since all of the parts you need are for higher rated axles than 3500 pounds. The races come already pressed into…

view full answer...

Answer 2

If the brakes in the picture are 12 x 2 inch brakes then yes, you can use #23-324 (left hand side) and #23-325 (right hand side). These brakes are rated for 5,200 pound axles and use the 5-bolt mounting pattern as the brake in your picture. The new…

view full answer...

Answer 3

The Hydraulic Brake Kit - Uni-Servo - Free Backing - 12" - Left/Right Hand Assemblies - 5.5K to 7K Item #AKFBBRK-7 looks like a similar fit. It sounds like you are just looking for the cylinder so based on the photos I recommend the Replacement…

view full answer...

Answer 4

Hey Ashley, thanks for the information! To replace a Atwood 85778 brake actuator, I recommend the Demco Hydraulic Brake Actuator item #DM62VR for drum brakes. It has the same 2" ball size and offers a bolt-on install for a 3" wide straight…

view full answer...

Answer 5

To add a gooseneck hitch to your 2024 GMC Sierra 2500 with a 6-3/4' bed, I recommend the B&W Custom Underbed Installation Kit item #BWGNRK1020. It has a massive 30,000 lbs capacity and fits both the 6-3/4' and 8' bed lengths. The…

view full answer...

Answer 6

The DICO 189 you referenced is the older version of the Titan 60. You will want to replace the master cylinder with the Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100. I've attached a video…

view full answer...

Answer 7

If you have standard size axles that you are installing the Electric Trailer Brake Kit #AKEBRK-7-SA on then you can choose from the following options: 5,200 lb Axle - Kit #BK3-310 (Grease Seal 2.125" ID) or Kit #BK3-300 (Grease Seal 2.250"…

view full answer...

Answer 8

Yes, Tekonsha released the part #3062-P which is a brake controller install harness that fits your 2019 Subaru Ascent and would work well. I attached a picture that shows where you'll find it on your vehicle too. For a brake controller I would…

view full answer...

Answer 9

Hello Greg, Yes, you can use the same drum for the electric brakes that you used with your hydraulic brakes. Based on the measurements you provided, it looks like you have a #84 spindle, which typically means you're working with a 3,500 lb axle.…

view full answer...

Answer 10

Hello Don. We do have the Replacement Wheel Cylinder for 10" and 12" Hydraulic Brakes, part #AKBRKR-H7-L for left hand side and part #AKBRKR-H7-R for right hand side. These will work with brake assemblies from most manufacturers, including…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Wheel Cylinder For Dexter 12-Inch Hydraulic Drum Brake Assembly

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching