Hole Diameter for Camco Cam Lock

Question

Question:

What diameter hole does this latch fit through?

asked by: Deck

0

Expert Reply:

The diameter hole that the Camco Cam Lock # CAM44323 fits into is 5/8 inches.

expert reply by: Charles S

0

Joseph

11/13/2021

I have a door 3/4" thick with a 1" hole. Do you have a lock assembly that would work for this? Thanks.

Les D.

11/18/2021

@Joseph Any chance you meant to say a 1 inch thick door with a 3/4" diameter opening? For that you could use the JR Products # 37200145 latch. A latch that will fit 3/4 inch thick door and has an opening that it 1 inch in diameter is a non-standard size, and we do not have that. You would have to find something like a bushing/spacer sleeve to go on the the lock cylinder to make a tight fit. You might also be able to drill a new 3/4” hole for a new lock, and fill in the old hole?

Answer 1

Hi Merrill; it sounds like you're looking for a complete replacement. The Ventline Breeze LED 360 Bathroom Vent w/ 120V AC Fan - 50 CFM - White #VE76FR is the direct replacement for the old V2280-50.

view full answer...

Answer 2

Hey Bob, we have just what you are looking for with the Timbren kit part #TDDF974A. This was designed to fit the front suspension of your 2020 Ram 2500 to provide extra suspension support when carrying plows so it will get rid of the sagging you are…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Hole Diameter for Camco Cam Lock

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching