Will MagnaFlow Performance Muffler Work With Diesel Engines

Question

Question:

Hello. Please need some information about magnaflow muffler MF11365 May use it for diesel engine? If no.Please could you offer me magnaflow mufflers that fit turbo diesel engine with follow dimensions: oval 4/9 or 5/8 inch Inlet/ outlet 2.25 inch,center/ offset,body length 11 inch,overall 17 inch,Bi-directional. Or round 7 inch,inlet/ outlet 2.25 inch,body length 11/14 inch,overall 17/20 inch,Bi-directional. I need for custom instalation. If you have some pictures or link to see what looks like will be great. Thanks in advance and Best Regards.

asked by: Vlado A

1

Helpful Expert Reply:

The MagnaFlow Performance Muffler, part # MF11365 is a Universal muffler and can be used for gas or diesel engines.

The inlet and outlet dimensions and length are what you need to make sure will fit for your application. The inlet and outlet for this muffler is 2-1/4 inches and the overall length is 17-inches.

expert reply by: Jeffrey L

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Will MagnaFlow Performance Muffler Work With Diesel Engines

Product Page this Question was Asked From

Continue Researching