Replacement Bolts and Serrated Washers for Reese Trunnion Bar Weight Distribution System

Question

Question:

I NEED 2 TRUNION SERATED WASHERS AND 2 BOLTS IN STAINLESS STEEL OR CHROME...IF YOU SELL THEM PLEASE LET ME KNOW THE COST AND PART NUMBER SO I CAN ORDER THEM.

asked by: ANTHONY

0

Expert Reply:

If you have a Reese weight distribution system then we have replacement bolts and washers # 58133. The bolts are not stainless steel or chrome. For that you would have to get some locally rated grade 8.

If you want just the washers use # 58024.

expert reply by: Michael H

0

Answer 1

I reached out to my tech contact at Reese and the 21210 bars are a fit for the Replacement Head and Shank for Reese Weight Distribution Systems #RP54980 and are rated for up to 1000 lbs based on what we can find. They said if you look under the bars…

view full answer...

Answer 2

Part #58024 is one pair of square washers with teeth for Weight Distribution heads.

view full answer...

Answer 3

I spoke to my contact at Kat's and they informed me that the Kat's Heaters Handi-Heat Magnum Magnetic Heater part #KH1190 draws about 3 amps of current.

view full answer...

Answer 4

Hi Michael; the washers are only available with the complete Replacement Ball Mount Hardware Kit for Reese Pro Round Bar WD Hitch - Spacer and Bolt Service Kit #RP38KR. Reese doesn't offer them separately. It wouldn't be a bad idea to have…

view full answer...

Answer 5

I wish we could help but that's not a Reese part number we are able to get at this time.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Bolts and Serrated Washers for Reese Trunnion Bar Weight Distribution System

Continue Researching